PIC18F1220ESLASHSSSQTP datasheet(152/308 Pages) MICROCHIP

152 / 308 page

PIC18F1220/1320

DS39605F-page 150

16.4.2

EUSART SYNCHRONOUS MASTER

RECEPTION

Once Synchronous mode is selected, reception is

enabled by setting either the Single Receive Enable bit,

SREN (RCSTA<5>), or the Continuous Receive

Enable bit, CREN (RCSTA<4>). Data is sampled on the

RB4/AN6/RX/DT/KBI0 pin on the falling edge of the

clock.

If enable bit, SREN, is set, only a single word is

received. If enable bit, CREN, is set, the reception is

continuous until CREN is cleared. If both bits are set,

then CREN takes precedence.

To set up a Synchronous Master Reception:

Initialize the SPBRGH:SPBRG registers for the

appropriate baud rate. Set or clear the BRGH

and BRG16 bits, as required, to achieve the

desired baud rate.

Enable the synchronous master serial port by

setting bits SYNC, SPEN and CSRC.

Ensure bits CREN and SREN are clear.

If interrupts are desired, set enable bit RCIE.

If 9-bit reception is desired, set bit RX9.

If a single reception is required, set bit SREN.

For continuous reception, set bit CREN.

Interrupt flag bit, RCIF, will be set when reception

is complete and an interrupt will be generated if

the enable bit, RCIE, was set.

Read the RCSTA register to get the 9th bit (if

enabled) and determine if any error occurred

during reception.

Read the 8-bit received data by reading the

RCREG register.

10. If any error occurred, clear the error by clearing

bit CREN.

11. If using interrupts, ensure that the GIE and PEIE

bits in the INTCON register (INTCON<7:6>) are

set.

FIGURE 16-12:

SYNCHRONOUS RECEPTION (MASTER MODE, SREN)

CREN bit

RB4/AN6/RX/

RB1/AN5/TX/

Write to

bit SREN

SREN bit

RCIF bit

(Interrupt)

Read

RXREG

Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

‘0’

bit 0

bit 1

bit 2

bit 3

bit 4

bit 5

bit 6

bit 7

‘0’

Q1 Q2 Q3 Q4

Note:

Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.

RB1/AN5/TX/

CK/INT1 pin

DT/KBI0 pin

(SCKP = 0)

(SCKP = 1)

PIC18F1220E/SSSQTP 데이터시트(PDF) 152 Page - Microchip Technology

PIC18F1220E/SSSQTP 데이터시트(HTML) 152 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL