| 전자부품 데이터시트 검색엔진 |
|
LTC2970CUFD 데이터시트(PDF) 26 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC2970CUFD 데이터시트(HTML) 26 Page - Linear Technology |
|
26 / 36 page ![]() LTC2970/LTC2970-1 26 29701fc OPERATIO Procedure: Update the over-voltage limit register with the value above which the ADC result should generate an over-voltage fault. Instantaneous over-voltage faults are updated after each ADC conversion. They are asserted high when the ADC result is greater than the over-voltage limit. They are cleared if the ADC result is less than or equal to the over-voltage limit. Setting the over-voltage limit to 14’h3fff inhibits instantaneous faults for the associated channel. Update the under-voltage limit register with the value below which the ADC result should generate an under-voltage fault. Instantaneous under-voltage faults are updated after each ADC conversion. They are asserted high when the ADC result is less than the under-voltage limit. They are cleared if the ADC result is greater than or equal to the under-voltage limit. Setting the over-voltage limit to 14’h4000 inhibits instantaneous faults for the associated channel. Update ADC_MON() control bits to allow ADC conversions on all channels that are to be monitored for over and under voltage limits. Instantaneous IDAC faults are polled after all ADC conversions are completed and set when the as- sociated IDAC registers are at ‘h00 of ‘hff. Read FAULT() to view the value of all instantaneous faults. The IO(Io_cfg_0) command may be used to configure the GPIO_0 pin to output the internal Power_good flag. Power_good is asserted high if there are no instantaneous over-voltage or under-voltage faults. IO() may be used to read the value of Power_good through io_gpio_0. The IO(Io_cfg_1) command may be used to configure the GPIO_1 pin to output the internal Idac_fault flag. Idac_fault is asserted high if either IDAC value is faulted. IO() may be used to read the value of Idac_fault through io_gpio_1. Rules: The over-voltage and under-voltage limits must be initial- ized; they do not have a default value. All over-voltage limits, under-voltage limits and ADC re- sults use 2’s complement notation with bit position [14] of register [14:0] being used for the sign. Instantaneous Ch0_a and Ch1_a faults may be used to trigger a servo on fault event. Over-voltage and under-voltage faults require that the associated ADC_MON control bit be asserted high for instantaneous fault detection to be updated. 17. Generating and Monitoring Latched Faults The LTC2970 is able to selectively latch instantaneous faults in the latched fault register FAULT_LA. Each instantaneous fault has an associated latched fault bit in FAULT_LA and a fault enable bit in FAULT_EN; (see Table 8) for details. When an instantaneous fault enable bit is high, any event that sets the instantaneous fault will simultaneously set the latched fault. The latched fault will remain set even if conditions permit the instantaneous fault to be cleared. The latched faults are immediately cleared whenever the associated fault enable bit is cleared. All latched faults are also cleared when the latched fault register is read over FAULT_LA(). The FAULT_INDEX() command may be read to determine if any latched faults are asserted. Reading FAULT_INDEX() does not clear latched faults. The ALERT output may also be configured to view whether any latched faults are as- serted. Procedure: Follow procedure for generating instantaneous faults. Write FAULT_EN() to enable any combination of latched faults. Read FAULT_INDEX() to determine if any latched faults are asserted without clearing latched faults. Read FAULT_LA() to monitor all latched faults. Reading FAULT_LA() will clear all latched faults. These will remain clear until the next time the LTC2970 polls and sets an associated instantaneous fault. Setting IO(Io_alert_enb) low will cause ALERT to be as- serted low whenever any one of the fourteen latched faults is asserted high. The value of the ALERT pin may also be read through IO(Alertb). |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |