전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

LTC1668I 데이터시트(PDF) 6 Page - Linear Technology

부품명 LTC1668I
상세설명  16-Bit, 50Msps DAC
PDF  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  LINER [Linear Technology]
홈페이지  http://www.linear.com
Logo LINER - Linear Technology

LTC1668I 데이터시트(HTML) 6 Page - Linear Technology

Back Button LTC1668I Datasheet HTML 2Page - Linear Technology LTC1668I Datasheet HTML 3Page - Linear Technology LTC1668I Datasheet HTML 4Page - Linear Technology LTC1668I Datasheet HTML 5Page - Linear Technology LTC1668I Datasheet HTML 6Page - Linear Technology LTC1668I Datasheet HTML 7Page - Linear Technology LTC1668I Datasheet HTML 8Page - Linear Technology LTC1668I Datasheet HTML 9Page - Linear Technology LTC1668I Datasheet HTML 10Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 6 / 16 page
background image
6
LTC1668
APPLICATIO S I FOR ATIO
Theory of Operation
The LTC1668 is a high speed current steering 16-Bit DAC
made on an advanced BiCMOS process. Precision thin
film resistors and well matched bipolar transistors result
in excellent DC linearity and stability. A low glitch current
switching design gives excellent AC performance at sample
rates up to 50Msps. The device is complete with a 2.5V
internal bandgap reference and edge triggered latches,
and sets a new standard for DAC applications requiring
very high dynamic range at output frequencies up to
several megahertz.
Referring to the Block Diagram, the DAC contains an array
of current sources that are steered to IOUTA or IOUTB with
NMOS differential current switches. The four most signifi-
cant bits, DB15 to DB12 are made up of 15 current
segments of equal weight. The lower bits, DB11 to DB0 are
binary weighted, using a combination of current scaling
and a differential resistive attenuator ladder. All bits and
segments are precisely matched, both in current weight
for DC linearity, and in switch timing for low glitch impulse
and low spurious tone AC performance.
Setting the Full-Scale Current, IOUTFS
The full-scale DAC output current, IOUTFS, is nominally
10mA, and can be adjusted down to 1mA. Placing a
resistor, RSET, between the REFOUT pin, and the IREFIN pin
sets IOUTFS as follows.
The internal reference control loop amplifier maintains a
virtual ground at IREFIN by servoing the internal current
source, IINT, to sink the exact current flowing into IREFIN.
IINT is a scaled replica of the DAC current sources and
IOUTFS = 8 • (IINT), therefore:
IOUTFS = 8 • (IREFIN) = 8 • (VREF/RSET)
(1)
For example, if RSET = 2k and is tied to VREF = REFOUT =
2.5V, IREFIN = 2.5/2k = 1.25mA and IOUTFS = 8 • (1.25mA)
= 10mA.
The reference control loop requires a capacitor on the
COMP1 pin for compensation. For optimal AC perfor-
mance, CCOMP1 should be connected to VSS and be placed
very close to the package (less than 0.1").
For fixed reference voltage applications, CCOMP1 should
be 0.1
µF or more. The reference control loop small-signal
bandwidth is approximately 1/(2
π)•CCOMP1•80or20kHz
for CCOMP1 = 0.1µF.
Internal Reference Output—REFOUT
The onboard 2.5V bandgap voltage reference drives the
REFOUT pin. It is trimmed and specified to drive a 2k
resistor tied from REFOUT to IREFIN, corresponding to a
1.25mA load (IOUTFS = 10mA). REFOUT has nominal
output impedance of 6
Ω, or 0.24% per mA, so it must be
buffered to drive any additional external load. A 0.1
µF
capacitor is required on the REFOUT pin for compensa-
tion. Note that this capacitor is required for stability, even
if the internal reference is not being used.
DAC Transfer Function
The LTC1668 uses straight binary digital coding. The
complementary current outputs, IOUT A and IOUT B, sink
current from 0 to IOUTFS. For IOUTFS = 10mA (nominal),
IOUT A swings from 0mA when all bits are low (i.e., Code =
0) to 10mA when all bits are high (i.e., Code = 65535) (deci-
mal representation). IOUT B is complementary to IOUT A.
IOUT A and IOUT B are given by the following formulas:
IOUT A = IOUTFS • (DAC Code/65536)
(2)
IOUT B = IOUTFS • (65535-DAC Code)/65536
(3)
In typical applications, the LTC1668 differential output
currents either drive a resistive load directly or drive an
equivalent resistive load through a transformer, or as the
feedback resistor of an I-to-V converter. The voltage
outputs generated by the IOUT A and IOUT B output currents
are then:
VOUT A = IOUT A • RLOAD
(4)
VOUT B = IOUT B • RLOAD
(5)
The differential voltage is:
VDIFF = VOUT A – VOUT B
(6)
= (IOUT A – IOUT B) • (RLOAD)



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com