ATmega16 datasheet(248/315 Pages) ATMEL

248 / 315 page

248

ATmega16(L)

2466E–AVR–10/02

Performing Page Erase by

SPM

To execute Page Erase, set up the address in the Z-pointer, write “X0000011” to

SPMCR and execute SPM within four clock cycles after writing SPMCR. The data in R1

and R0 is ignored. The page address must be written to PCPAGE in the Z-register.

Other bits in the Z-pointer must be written zero during this operation.

•

Page Erase to the RWW section: The NRWW section can be read during the page

erase.

•

Page Erase to the NRWW section: The CPU is halted during the operation.

Filling the Temporary Buffer

(Page Loading)

To write an instruction word, set up the address in the Z-pointer and data in R1:R0, write

“00000001” to SPMCR and execute SPM within four clock cycles after writing SPMCR.

The content of PCWORD in the Z-register is used to address the data in the temporary

buffer. The temporary buffer will auto-erase after a page write operation or by writing the

RWWSRE bit in SPMCR. It is also erased after a system reset. Note that it is not possi-

ble to write more than one time to each address without erasing the temporary buffer.

Performing a Page Write

To execute Page Write, set up the address in the Z-pointer, write “X0000101” to

SPMCR and execute SPM within four clock cycles after writing SPMCR. The data in R1

and R0 is ignored. The page address must be written to PCPAGE. Other bits in the Z-

pointer must be written zero during this operation.

•

Page Write to the RWW section: The NRWW section can be read during the Page

Write.

•

Page Write to the NRWW section: The CPU is halted during the operation.

Using the SPM Interrupt

If the SPM interrupt is enabled, the SPM interrupt will generate a constant interrupt

when the SPMEN bit in SPMCR is cleared. This means that the interrupt can be used

instead of polling the SPMCR Register in software. When using the SPM interrupt, the

Interrupt Vectors should be moved to the BLS section to avoid that an interrupt is

accessing the RWW section when it is blocked for reading. How to move the interrupts

is described in “Interrupts” on page 42.

Consideration while Updating

BLS

Special care must be taken if the user allows the Boot Loader section to be updated by

leaving Boot Lock bit11 unprogrammed. An accidental write to the Boot Loader itself can

corrupt the entire Boot Loader, and further software updates might be impossible. If it is

not necessary to change the Boot Loader software itself, it is recommended to program

the Boot Lock bit11 to protect the Boot Loader software from any internal software

changes.

Prevent Reading the RWW

Section during Self-

Programming

During Self-Programming (either Page Erase or Page Write), the RWW section is

always blocked for reading. The user software itself must prevent that this section is

addressed during the Self-Programming operation. The RWWSB in the SPMCR will be

set as long as the RWW section is busy. During self-programming the Interrupt Vector

table should be moved to the BLS as described in “Interrupts” on page 42, or the inter-

rupts must be disabled. Before addressing the RWW section after the programming is

completed, the user software must clear the RWWSB by writing the RWWSRE. See

“Simple Assembly Code Example for a Boot Loader” on page 250 for an example.

Setting the Boot Loader Lock

Bits by SPM

To set the Boot Loader Lock bits, write the desired data to R0, write “X0001001” to

SPMCR and execute SPM within four clock cycles after writing SPMCR. The only

accessible Lock bits are the Boot Lock bits that may prevent the Application and Boot

Loader section from any software update by the MCU.

Bit

543210

BLB12

BLB11

BLB02

BLB01

ATMEGA16 데이터시트(PDF) 248 Page - ATMEL Corporation

ATMEGA16 데이터시트(HTML) 248 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL