AM29F002NB datasheet(14/40 Pages) AMD

14 / 40 page

November 28, 2000

Am29F002B/Am29F002NB

DQ7 or DQ6. See “Write Operation Status” for informa-

tion on these status bits.

Any commands written to the device during the

Embedded Program Algorithm are ignored. On the

Am29F002B only, note that a hardware reset during

the sector erase operation immediately terminates the

operation. The Sector Erase command sequence

should be reinitiated once the device has returned to

reading array data, to ensure data integrity.

Programming is allowed in any sequence and across

sector boundaries. A bit cannot be programmed

from a “0” back to a “1”. Attempting to do so may halt

the operation and set DQ5 to “1”, or cause the Data#

Polling algorithm to indicate the operation was suc-

cessful. However, a succeeding read will show that the

data is still “0”. Only erase operations can convert a “0”

to a “1”.

Note: See the appropriate Command Definitions table for

program command sequence.

Figure 2.

Program Operation

Chip Erase Command Sequence

Chip erase is a six-bus-cycle operation. The chip erase

command sequence is initiated by writing two unlock

cycles, followed by a set-up command. Two additional

unlock write cycles are then followed by the chip erase

command, which in turn invokes the Embedded Erase

algorithm. The device does not require the system to

preprogram prior to erase. The Embedded Erase algo-

rithm automatically preprograms and verifies the entire

memory for an all zero data pattern prior to electrical

erase. The system is not required to provide any con-

trols or timings during these operations. The Command

Definitions table shows the address and data require-

ments for the chip erase command sequence.

A ny c om ma nds wr it t en to t he chi p du rin g t he

Embedded Erase algorithm are ignored. On the

Am29F002B only, note that a hardware reset during

the sector erase operation immediately terminates the

operation. The Sector Erase command sequence

should be reinitiated once the device has returned to

reading array data, to ensure data integrity.

The system can determine the status of the erase oper-

ation by using DQ7, DQ6, or DQ2. See “Writ e

Operation Status” for information on these status bits.

When the Embedded Erase algorithm is complete, the

device returns to reading array data and addresses are

no longer latched.

Figure 3 illustrates the algorithm for the erase opera-

tion. See the Erase/Program Operations tables in “AC

Characteristics” for parameters, and to the Chip/Sector

Erase Operation Timings for timing waveforms.

Sector Erase Command Sequence

Sector erase is a six bus cycle operation. The sector

erase command sequence is initiated by writing two

unlock cycles, followed by a set-up command. Two

additional unlock write cycles are then followed by the

address of the sector to be erased, and the sector

erase command. The Command Definitions table

shows the address and data requirements for the

sector erase command sequence.

The device does not require the system to preprogram

the memory prior to erase. The Embedded Erase algo-

rithm automatically programs and verifies the sector for

an all zero data pattern prior to electrical erase. The

system is not required to provide any controls or

timings during these operations.

After the command sequence is written, a sector erase

time-out of 50 µs begins. During the time-out period,

additional sector addresses and sector erase com-

mands may be written. Loading the sector erase buffer

may be done in any sequence, and the number of

sectors may be from one sector to all sectors. The time

between these additional cycles must be less than 50

µs, otherwise the last address and command might not

be accepted, and erasure may begin. It is recom-

mended that processor interrupts be disabled during

this time to ensure all commands are accepted. The

START

Write Program

Command Sequence

Data Poll

from System

Verify Data?

Yes

Last Address?

Yes

Programming

Completed

Increment Address

Embedded

Program

algorithm

in progress

AM29F002NB 데이터시트(PDF) 14 Page - Advanced Micro Devices

AM29F002NB 데이터시트(HTML) 14 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

데이터시트 다운로드

링크 URL