전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

DP83850CVF 데이터시트(PDF) 9 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
부품명 DP83850CVF
상세설명  100 Mb/s TX/T4 Repeater Interface Controller (100RIC??
PDF  37 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  NSC [National Semiconductor (TI)]
홈페이지  http://www.national.com
Logo NSC - National Semiconductor (TI)

DP83850CVF 데이터시트(HTML) 9 Page - National Semiconductor (TI)

Back Button DP83850CVF Datasheet HTML 5Page - National Semiconductor (TI) DP83850CVF Datasheet HTML 6Page - National Semiconductor (TI) DP83850CVF Datasheet HTML 7Page - National Semiconductor (TI) DP83850CVF Datasheet HTML 8Page - National Semiconductor (TI) DP83850CVF Datasheet HTML 9Page - National Semiconductor (TI) DP83850CVF Datasheet HTML 10Page - National Semiconductor (TI) DP83850CVF Datasheet HTML 11Page - National Semiconductor (TI) DP83850CVF Datasheet HTML 12Page - National Semiconductor (TI) DP83850CVF Datasheet HTML 13Page - National Semiconductor (TI) Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 37 page
background image
2.0 Pin Descriptions (Continued)
9
www.national.com
2.5 Pin Type Designation
PART[5:0]
O, L
—
Partition: Used to indicate each port's Jabber and Partition status. PART[3:0] cycle
through each port number (0-11) continuously. PART[4] indicates the Partition status
for each port (1 = Port Partitioned). PART[5] indicates the Jabber status for each port
(1 = Port Jabbering). These pins are intended to be decoded to drive LEDs.
RID_ER
O, L
high
Repeater ID Error: This pin is asserted under the conditions which set the RID_error
bit in the DEVICEID register.
RSM[3]
/RXECONFIG
I/O, L
—
Repeater State Machine Output/ RXE Polarity: This pin is an input during reset and
it is used to latch the desired polarity of RXE[11:0] signals.
When this pin is pulled high or it is unconnected, then the RXE signals become active
high. However, if this signal is pulled low, then the RXE signals become active low.
In all other non-reset times, this pin reflects the output of the Repeater State Machine.
RSM[3]
RSM[2:0]
I/O, L O, L
—
Test Outputs indicating the state of the Repeater State Machine.
RSM[3:0]
State
0
idle
1
collision
2
one port left
3
repeat
4
noise
Other states are undefined.
MODE[1:0]
I
—
Mode Inputs: The 100RIC may be configured in the following modes:
MODE[1:0]
Operation
0,0
No special modes selected
1,0
Test mode
0,1
Test mode
1,1
Preamble regeneration (T4) mode
Note: A table showing pin type designation is given in section 2.5
Signal Name
Type
Active
Pin Description
Pin Type
Description
I
Input Buffer
O
Output Buffer, driven high or low at all times
I/O/Z
Bi-directional Buffer with high impedance output
O/Z
Output Buffer with high impedance capability
OC
Open Collector like signals. These buffers are
either driven low or in a high-impedance state.
L
Output low drive: 4 mA
M
Output medium drive: 12 mA
H
Output high drive : 24 mA



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com