SC431B datasheet(4/17 Pages) ONSEMI

4 / 17 page

NCP431A, SC431A, NCP431B, SC431B, NCP432B, SC432B Series

www.onsemi.com

ELECTRICAL CHARACTERISTICS (TA = 25°C, unless otherwise noted.)

Symbol

Characteristic

NCP431BC

NCP432BC

NCP431BI

NCP432BI

NCP/SC431BV

NCP/SC432BV

Unit

Min

Typ

Max

Min

Typ

Max

Min

Typ

Max

Vref

Reference Input Voltage

VKA = Vref, IK = 1 mA

TA = 25°C

TA = Tlow to Thigh (Figure 3, Note 7)

2.4875

2.500

2.5125

2.4875

2.4775

2.500

2.5125

2.4875

2.4725

2.500

2.5125

DVrefT

Reference Input Voltage Deviation Over Tem-

perature Range (Figure 3, Notes 8, 9)

VKA= Vref, IK = 1 mA

−

5.0

1−

−

DVref

DVKA

Ratio of Change in Reference Input Voltage to

Change in Cathode to Anode Voltage

IK = 1 mA (Figure 4),

DVKA = 10 V to Vref

DVKA = 36 V to 10 V

−

−1.85

−0.80

−3.1

−1.8

−

−1.85

−0.80

−3.1

−1.8

−

−1.85

−0.80

−3.1

−1.8

mV/

Iref

Reference Input Current (Figure 4)

IK = 1 mA, R1 = 220 k, R2 = R

TA = −40°C to +125°C

−

190

−

190

−

190

DIrefT

Reference Input Current Deviation Over Tem-

perature Range (Figure 4, Note 8)

IK = 1 mA, R1 = 10 k, R2 = R

−

Imin

Minimum Cathode Current For Regulation

VKA = Vref (Figure 3)

−

Ioff

Off−State Cathode Current (Figure 5)

VKA = 36 V, Vref = 0 V

−

180

1000

−

180

1000

−

180

1000

|ZKA|

Dynamic Impedance (Figure 3, Note 10)

VKA = Vref, DIK = 1.0 mA to 100 mA

v 1.0 kHz

−

0.22

0.5

−

0.22

0.5

−

0.22

0.5

7. Tlow

= −40

°C for NCP431BI, NCP431BV, NCP432BI, NCP432BV, SC431B, SC432B

= 0

°C for NCP431BC, NCP432BC

Thigh = 70°C for NCP431BC, NCP432BC

= 85

°C for NCP431BI, NCP432BI

= 125

°C for NCP431BV, NCP432BV, SC431BV, SC432BV

8. Guaranteed by design

9. The deviation parameter

DVrefT is defined as the difference between the maximum and minimum values obtained over the full operating

ambient temperature range that applies.

The average temperature coefficient of the reference input voltage, Vref is defined as:

ref

ppm

° C

ref

@25

° C

106

ref

106

ref

@25

° C

aVref can be positive or negative depending on whether Vref Min or Vref Max occurs at the lower ambient temperature.

Example:

DVrefT = 17 mV and slope is positive

Vref = 2.5 V, DTA = 165°C (from −40°C to +125°C)

ref +

0.017

@ 106

165

@ 2.5

+ 41.2 ppm ° C

10. The dynamic impedance ZKA is defined as: (|ZKA| = (DVKA/DIK). When the device is programmed with two external resistors, R1 and R2,

the total dynamic impedance of the circuit is defined as: |ZKA’| [ |ZKA| (1 + (R1/R2))

11. SC431BVSNT1G, SC432BVSNT1G − Tlow = −40°C, Thigh = 125°C. Guaranteed by design. SC Prefix for Automotive and Other Applica-

tions Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable.

Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product

performance may not be indicated by the Electrical Characteristics if operated under different conditions.

SC431B 데이터시트(PDF) 4 Page - ON Semiconductor

SC431B 데이터시트(HTML) 4 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

데이터시트 다운로드

링크 URL