STM32L475RC datasheet(83/193 Pages) STMICROELECTRONICS

83 / 193 page

DocID027692 Rev 2

83/193

STM32L475xx

Electrical characteristics

181

1. All main power (VDD, VDDA, VDDUSB, VBAT) and ground (VSS, VSSA) pins must always be connected to the external power

supply, in the permitted range.

2. VIN maximum must always be respected. Refer to Table 20: Current characteristics for the maximum allowed injected

current values.

3. This formula has to be applied only on the power supplies related to the IO structure described in the pin definition table.

4. To sustain a voltage higher than 4 V the internal pull-up/pull-down resistors must be disabled.

5. Include VREF- pin.

Table 20. Current characteristics

Symbol

Ratings

Max

Unit

∑IVDD

Total current into sum of all VDD power lines (source)(1)

150

∑IVSS

Total current out of sum of all VSS ground lines (sink)(1)

150

IVDD(PIN)

Maximum current into each VDD power pin (source)(1)

100

IVSS(PIN)

Maximum current out of each VSS ground pin (sink)(1)

100

IIO(PIN)

Output current sunk by any I/O and control pin except FT_f

Output current sunk by any FT_f pin

Output current sourced by any I/O and control pin

∑IIO(PIN)

Total output current sunk by sum of all I/Os and control pins(2)

100

Total output current sourced by sum of all I/Os and control pins(2)

100

IINJ(PIN)(3)

Injected current on FT_xxx, TT_xx, RST and B pins, except PA4,

PA5

-5/+0(4)

Injected current on PA4, PA5

-5/0

∑|IINJ(PIN)|

Total injected current (sum of all I/Os and control pins)(5)

1. All main power (VDD, VDDA, VDDUSB, VBAT) and ground (VSS, VSSA) pins must always be connected to the external power

supplies, in the permitted range.

2. This current consumption must be correctly distributed over all I/Os and control pins. The total output current must not be

sunk/sourced between two consecutive power supply pins referring to high pin count QFP packages.

3. Positive injection (when VIN > VDDIOx) is not possible on these I/Os and does not occur for input voltages lower than the

specified maximum value.

4. A negative injection is induced by VIN < VSS. IINJ(PIN) must never be exceeded. Refer also to Table 19: Voltage

characteristics for the minimum allowed input voltage values.

5. When several inputs are submitted to a current injection, the maximum ∑|IINJ(PIN)| is the absolute sum of the negative

injected currents (instantaneous values).

Table 21. Thermal characteristics

Symbol

Ratings

Value

Unit

TSTG

Storage temperature range

–65 to +150

°C

Maximum junction temperature

150

°C

STM32L475RC 데이터시트(PDF) 83 Page - STMicroelectronics

STM32L475RC 데이터시트(HTML) 83 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL