| 전자부품 데이터시트 검색엔진 |
|
UCS1001 데이터시트(PDF) 59 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
UCS1001 데이터시트(HTML) 59 Page - Microchip Technology |
|
59 / 59 page ![]() USB Port Power Controller with Charger Emulation Datasheet SMSC UCS1001 59 Revision 1.2 (05-21-12) DATASHEET Revision 1.1 (11-21-11) cont. Section 8.4, "Data Pass- through (No Charger Emulation)" Data Pass-through persists until M1, M2, or EM_EN controls are changed. It is no longer affected by PWR_EN. Added application note: When the M1, M2, and EM_EN controls are set to ‘0’, ‘1’, ‘0’ or to ‘1’, ‘1’, ‘0’ respectively, Data Pass- through mode will persist if the PWR_EN control is disabled; however, the UCS1001 will draw more current. To leave Data Pass-through mode, the PWR_EN control must be enabled before the M1, M2, and EM_EN controls are changed to the desired mode. Section 8.6, "BC1.2 CDP" BC1.2 CDP mode uses constant current limiting. Added application note: BC1.2 compliance testing may require the S0 control to be set to ‘0’ (Attach and Removal Detection feature disabled) while testing is in progress. Added application note: When the UCSX100X is in BC1.2 CDP mode and the Attach and Removal Detection feature is enabled, if a power thief, such as a USB light or fan, attaches but does not assert DP, a Removal event will not occur when the portable device is removed. However, if a standard USB device is subsequently attached, Removal Detection will again be fully functional. As well, if PWR_EN is cycled or M1, M2, and / or EM_EN change state, a Removal event will occur and Attach Detection will be reactivated. Section 8.7, "BC1.2 DCP" Added application note: BC1.2 compliance testing may require the S0 control to be set to ‘0’ (Attach and Removal Detection feature disabled) while testing is in progress. Table 8.2, "Current Limit Mode Options" BC1.2 CDP charger emulation changed from using “trip” to “CC mode if ILIM < 1.5 A, otherwise, trip mode”. Section 8.10.4, "Legacy 5 Charger Emulation Profile" Added. The Legacy 5 charger emulation profile no longer applies a voltage divider. It applies 900 mV to DPOUT and DMOUT. Revision 1.0 (08-18-11) Initial Release Table 11.1 Customer Revision History (continued) REVISION LEVEL & DATE SECTION/FIGURE/ENTRY CORRECTION |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |