| 전자부품 데이터시트 검색엔진 |
|
HY29F080 데이터시트(PDF) 18 Page - Hynix Semiconductor |
|
|
|||||||||||||||||||||||||||||
HY29F080 데이터시트(HTML) 18 Page - Hynix Semiconductor |
|
18 / 38 page ![]() 18 Rev. 6.1/May 01 HY29F080 DQ[3] - Sector Erase Timer After writing a Sector Erase command sequence, the host may read DQ[3] to determine whether or not an erase operation has begun. When the sector erase time-out expires and the sector erase operation commences, DQ[3] switches from a ‘0’ to a ‘1’. Refer to the “Sector Erase Command” section for additional information. Note that the sector erase timer does not apply to the Chip Erase command. After the initial Sector Erase command sequence is issued, the system should read the status on DQ[7] (Data# Polling) or DQ[6] (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ[3]. If DQ[3] is a ‘1’, the internally controlled erase cycle has begun and all further sector erase data cycles or commands (other than Erase Suspend) are ignored until the erase operation is complete. If DQ[3] is a ‘0’, the device will accept a sector erase data cycle to mark an additional sector for erasure. To ensure that the data cycles have been accepted, the system software should check the status of DQ[3] prior to and following each subsequent sector erase data cycle. If DQ[3] is high on the second status check, the last data cycle might not have been accepted. HARDWARE DATA PROTECTION The HY29F080 provides several methods of pro- tection to prevent accidental erasure or program- ming which might otherwise be caused by spuri- ous system level signals during V CC power-up and power-down transitions, or from system noise. These methods are described in the sections that follow. Command Sequences Commands that may alter array data require a sequence of cycles as described in Table 5. This provides data protection against inadvertent writes. Low V CC Write Inhibit To protect data during V CC power-up and power- down, the device does not accept write cycles when V CC is less than VLKO (typically 3.7 volts). The command register and all internal program/erase circuits are disabled, and the device resets to the Read mode. Writes are ignored until V CC is greater than V LKO . The system must provide the proper signals to the control pins to prevent unintentional writes when V CC is greater than VLKO. Write Pulse “Glitch” Protection Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle. Logical Inhibit Write cycles are inhibited by asserting any one of the following conditions: OE# = V IL , CE# = VIH, or WE# = V IH. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a logical one. Power-Up Write Inhibit If WE# = CE# = V IL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the Read mode on power- up. Sector Group Protection Additional data protection is provided by the HY29F080’s sector group protect feature, de- scribed previously, which can be used to protect sensitive areas of the Flash array from accidental or unauthorized attempts to alter the data. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |