전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

L99MM70XP 데이터시트(PDF) 29 Page - STMicroelectronics

부품명 L99MM70XP
상세설명  INH input for external CAN transceiver
PDF  68 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  STMICROELECTRONICS [STMicroelectronics]
홈페이지  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

L99MM70XP 데이터시트(HTML) 29 Page - STMicroelectronics

Back Button L99MM70XP Datasheet HTML 25Page - STMicroelectronics L99MM70XP Datasheet HTML 26Page - STMicroelectronics L99MM70XP Datasheet HTML 27Page - STMicroelectronics L99MM70XP Datasheet HTML 28Page - STMicroelectronics L99MM70XP Datasheet HTML 29Page - STMicroelectronics L99MM70XP Datasheet HTML 30Page - STMicroelectronics L99MM70XP Datasheet HTML 31Page - STMicroelectronics L99MM70XP Datasheet HTML 32Page - STMicroelectronics L99MM70XP Datasheet HTML 33Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 29 / 68 page
background image
L99MM70XP
Protection and diagnosis
Doc ID 022637 Rev 2
29/68
If the output current exceeds the current shutdown threshold the output transistor is turned
off and the corresponding diagnosis bit of the output is latched. The status can be read and
cleared from SPI. If the overcurrent recovery mode is set for this output, the output is
switched on again in order to provide a soft start function (see Section 3.10.5:
Programmable soft start function) and the status bit is cleared automatically. Otherwise the
output stays off until the status bit is cleared.
The outputs are automatically switched off in case of passive mode, VS undervoltage, VS
overvoltage, thermal shutdown (TSD1 and TSD2) or stuck at 1/0 condition at DI.
4.5
High-side driver outputs
The device provides a total of 4 high-side outputs OUT6,7,8,9 to drive LED or defroster.
The high-side outputs are protected against
●
Overvoltage and undervoltage (can be masked by SPI)
●
Overload (short circuit)
●
Overtemperature with pre warning
If the output current exceeds the current shutdown threshold the output transistor is turned
off and the corresponding diagnosis bit of the output is latched. The status can be read and
cleared from SPI. If the overcurrent recovery mode is set for this output, the output is
switched on again in order to provide a soft start function (see Section 3.10.5:
Programmable soft start function) and the status bit is cleared automatically. Otherwise the
output stays off until the status bit is cleared.
The outputs are automatically switched off in case of passive mode, VS undervoltage, VS
overvoltage, thermal shutdown (TSD1 and TSD2) or stuck at 1/0 condition at DI.
Note:
Loss of ground or ground shift with externally grounded loads: ESD structures are
configured for nominal currents only. If external loads are connected to different grounds, the
current load must be limited to this nominal current.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com