TNETV1644ZDU6 datasheet(187/306 Pages) TI1

187 / 306 page

TMS320DM6437

Digital Media Processor

www.ti.com

SPRS345D – NOVEMBER 2006 – REVISED JUNE 2008

Default Power Down Pins

As discussed in Section 3.2, Power Considerations, the VDD3P3V_PWDN register controls power to the

3.3-V pins. The VDD3P3V_PWDN register defaults to powering down some 3.3-V pins to save power. For

more details on the VDD3P3V_PWDN register and which 3.3-V pins default to powerup or powerdown,

Section 3.2, Power Considerations. The pins that default to powerdown, are both reset to powerdown and

high-impedance. They remain in that state until configured otherwise by VDD3P3_PWDN and

PINMUX0/PINMUX1 programming.

• Default Power Down Pin Group: GP[4]/PWM1, ACLKR0/CLKX0/GP[99], AFSR0/DR0/GP[100],

AHCLKR0/CLKR0/GP[101], AXR0[3]/FSR0/GP[102], AXR0[2]/FSX0/GP[103], AXR0[1]/DX0/GP[104],

AXR0/FSR1/GP[105], ACLKX0/CLKX1/GP[106], AFSX0/DX1/GP[107], AHCLKX0/CLKR1/GP[108],

AMUTEIN0/FSX1/GP[109], AMUTE0/DR1/GP[110], HECC_TX/TOUT1L/UTXD1/GP[55],

HECC_RX/TINP1L/URXD1/GP[56], CLKS0/TOUT0L/GP[97], CLKS1/TINP0L/GP[98], URXD0/GP[85],

UTXD0/GP[86], UCTS0/GP[87], and URTS0/PWM0/GP[88].

All Other Pins

During RESETOUT assertion (low), all other pins are controlled by the default peripheral. The default

peripheral is determined by the default settings of the PINMUX0 or PINMUX1 registers.

Some of the PINMUX0/PINMUX1 settings are determined by configuration pins latched at reset. To

determine the reset behavior of these pins, see Section 3.7, Multiplexed Pin Configurations and read the

rest of the this subsection to understand how that default peripheral controls the pin.

The reset behaviors for all these other pins are categorized as follows (also see Figure 6-7 and Figure 6-8

in Section 6.5.9, Reset Electrical Data/Timing):

• Z+/Low Group (Z Longer-to-Low Group): These pins are 3-stated when device-level global reset

source (e.g., POR, RESET, or Max Reset) is asserted. These pins remain 3-stated throughout

RESETOUT assertion. When RESETOUT is deasserted, these pins drive a logic low.

• Z+/High Group (Z Longer-to-High Group): These pins are 3-stated when device-level global reset

source (e.g., POR, RESET, or Max Reset) is asserted. These pins remain 3-stated throughout

RESETOUT assertion. When RESETOUT is deasserted, these pins drive a logic high.

• Z+/Invalid Group (Z Longer-to-Invalid Group): These pins are 3-stated when device-level global

reset source (e.g., POR, RESET, or Max Reset) is asserted. These pins remain 3-stated throughout

RESETOUT assertion. When RESETOUT is deasserted, these pins drive an invalid value until

configured otherwise by their respective peripheral (after the peripheral is enabled by the PSC).

• Z Group: These pins are 3-stated by default, and these pins remain 3-stated throughout RESETOUT

assertion. When RESETOUT is deasserted, these pins remain 3-stated until configured otherwise by

their respective peripheral (after the peripheral is enabled by the PSC).

• Low Group: These pins are low by default, and remain low until configured otherwise by their

respective peripheral (after the peripheral is enabled by the PSC).

• High Group: These pins are high by default, and remain high until configured otherwise by their

respective peripheral (after the peripheral is enabled by the PSC).

• Z/Low Group (Z-to-Low Group): These pins are 3-stated when device-level global reset source (e.g.,

POR, RESET, or Max Reset) is asserted. When the reset source is deasserted, these pins drive a

logic low.

• Z/High Group (Z-to-High Group): These pins are 3-stated when device-level global reset source

(e.g., POR, RESET, or Max Reset) is asserted. When reset source is deasserted, these pins drive a

logic high.

• Clock Group: These clock pins are toggling by default. They paused momentarily before RESETOUT

is deasserted (high). The only pin in the Clock Group is CLKOUT0.

This is a list of possible default peripherals and how they control the pins during reset:

• GPIO: All GPIO pins behave according to Z Group.

Note: The following EMIFA list only includes pins that can default to function as EMIFA signals.

Submit Documentation Feedback

Peripheral Information and Electrical Specifications

187

TNETV1644ZDU6 데이터시트(PDF) 187 Page - Texas Instruments

TNETV1644ZDU6 데이터시트(HTML) 187 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL