| 전자부품 데이터시트 검색엔진 |
|
WM8255 데이터시트(PDF) 42 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
WM8255 데이터시트(HTML) 42 Page - Cirrus Logic |
|
42 / 49 page ![]() Production Data WM8255 w PD, Rev 4.7, August 2013 42 REGISTER BIT NO BIT NAME(S) DEFAULT DESCRIPTION Setup Register 2 0 POSNEG 0 When VSMPDET = 0 this bit has no effect. When VSMPDET = 1 this bit controls whether positive or negative edges are detected: 0 = Negative edge on VSMP pin is detected and used to generate internal timing pulse. 1 = Positive edge on VSMP pin is detected and used to generate internal timing pulse. See Figure 27 for further details. 1 2BITOP 0 Changes the digital output from 4 bit muxed to 2 bit muxed output. 2 INVOP 0 Digitally inverts the polarity of output data. 0 = negative going video gives negative going output, 1 = negative-going video gives positive going output data. 3 VRLCEXT 0 When set powers down the RLCDAC, changing its output to Hi-Z, allowing VRLC/VBIAS to be externally driven. 4 RLCINT 0 This bit is used to determine whether Reset Level Clamping is enabled. 0 = RLC disabled, 1 = RLC enabled. 5 Reserved 0 Must be set to zero. 7:6 DEL[1:0] 00 Sets the output latency in ADC clock periods. 1 ADC clock period = 2 MCLK periods except in Mode 2 where 1 ADC clock period = 3 MCLK periods. 00 = Minimum latency 01 = Delay by one ADC clock period 10 = Delay by two ADC clock periods 11 = Delay by three ADC clock periods Setup Register 3 3:0 RLCV[3:0] 0011 Controls RLCDAC driving VRLC pin to define single ended signal reference voltage or Reset Level Clamp voltage. See Electrical Characteristics section for ranges. 5:4 CDSREF[1:0] 01 CDS mode reset timing adjust. 00 = Advance 1 MCLK period 01 = Normal 10 = Retard 1 MCLK period 11 = Retard 2 MCLK periods 7:6 INTM[1:0] 00 Colour selection bits used in internal modes. 00 = Red, 01 = Green, 10 = Blue and 11 = Reserved. See Table 1 for details. Software Reset Any write to Software Reset causes all cells (including LED) to be reset. It is recommended that a software reset be performed after a power-up before any other register writes. Setup Register 4 2:0 VDEL[2:0] 000 When VSMPDET = 0 these bits have no effect. When VSMPDET = 1 these bits set a programmable delay from the detected edge of the signal applied to the VSMP pin. The internally generated pulse is delayed by VDEL MCLK periods from the detected edge. See Figure 27, Internal VSMP Pulses Generated for details. 5:3 Reserved 000 Must be set to zero 6 LEDIMAX 0 Sets the maximum current limit to one of two ranges (see electrical characteristics section). 7 Reserved 0 Must be set to zero Setup Register 5 7:0 LEDIDACR [7:0] 00100000 Fine LED current during imaging for Red LED Setup Register 6 7:0 LEDIDACG [7:0] 00100000 Fine LED current during imaging for Green LED Setup Register 7 7:0 LEDIDACB [7:0] 00100000 Fine LED current during imaging for Blue LED Setup Register 8 1:0 LEDIRNGR [1:0] 00 Coarse LED current range during imaging for Red LED 2 Reserved 0 Must be set to zero |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |