LM393DGKR datasheet(11/40 Pages) TI1

11 / 40 page

LM193, LM293, LM293A, LM393, LM393A, LM2903, LM2903V, LM393B, LM2903B

www.ti.com

SLCS005AA – OCTOBER 1979 – REVISED SEPTEMBER 2019

Product Folder Links: LM193 LM293 LM293A LM393 LM393A LM2903 LM2903V LM393B LM2903B

Submit Documentation Feedback

(1)

Full range (minimum or maximum) for LM2903 is –40°C to 125°C. All characteristics are measured with zero common-mode input

voltage, unless otherwise specified.

(2)

VCC MAX = 30 V for non-V devices and 32 V for V-suffix devices.

(3)

The voltage at either input should not be allowed to go negative by more than 0.3 V otherwise output may be incorrect and excessive

input current can flow. The upper end of the common-mode voltage range is limited by VCC – 2V. However only one input needs to be in

the valid common mode range, the other input can go up the maximum VCC level and the comparator provides a proper output state.

Either or both inputs can go to maximum VCC level without damage.

6.12 Electrical Characteristics for LM2903, LM2903V, and LM2903AV

at specified free-air temperature, VCC = 5 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS

(1)

LM2903, LM2903V

LM2903AV

UNIT

MIN

TYP

MAX

MIN

TYP

MAX

VIO

Input offset voltage

VCC = 5 V to MAX

(2) ,

VO = 1.4 V,

VIC = VICR(min),

25°C

Full range

IIO

Input offset current

VO = 1.4 V

25°C

Full range

200

IIB

Input bias current

VO = 1.4 V

25°C

–25

–250

–25

–250

Full range

–500

VICR

Common-mode input-

voltage range(3)

25°C

0 to

VCC – 1.5

0 to

VCC – 1.5

Full range

0 to

VCC – 2

0 to

VCC – 2

AVD

Large-signal differential-

voltage amplification

VCC = 15 V, VO = 1.4 V to 11.4 V,

RL ≥ 15 kΩ to VCC

25°C

100

V/mV

IOH

High-level output current

VOH = 5 V,

VID = 1 V

25°C

0.1

VOH = VCC MAX

(2),

VID = 1 V

Full range

µA

VOL

Low-level output voltage

IOL = 4 mA,

VID = –1 V,

25°C

150

400

150

400

Full range

700

IOL

Low-level output current

VOL = 1.5 V,

VID = –1 V

25°C

ICC

Supply current

RL = ∞

VCC = 5 V

25°C

0.8

VCC = MAX

Full range

2.5

(1)

CL includes probe and jig capacitance.

(2)

The response time specified is the interval between the input step function and the instant when the output crosses 1.4 V.

6.13 Switching Characteristics (all devices)

VCC = 5 V, TA = 25°C

PARAMETER

TEST CONDITIONS

TYP

UNIT

Response time

RL connected to 5 V through 5.1 kΩ,

CL = 15 pF

(1) (2)

100-mV input step with 5-mV overdrive

1.3

µs

TTL-level input step

0.3

LM393DGKR 데이터시트(PDF) 11 Page - Texas Instruments

LM393DGKR 데이터시트(HTML) 11 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

데이터시트 다운로드

링크 URL