68HC705JB3 datasheet(36/134 Pages) FREESCALE

36 / 134 page

GENERAL RELEASE SPECIFICATION

November 5, 1998

MOTOROLA

INTERRUPTS

MC68HC05JB3

4-6

REV 1

IRQPU — IRQ pin PUll-up resistor enable

This bit enables/disables the internal pull-up resistor on the IRQ pin.

1 =

Internal pull-up resistor in IRQ pin enabled.

0 =

Internal pull-up resistor in IRQ pin disabled.

IRQR — IRQ Interrupt Acknowledge

This write-only bit clears an IRQ interrupt by clearing the IRQ latch, and hence

the IRQF bit. The IRQR bit will always read as a logic zero.

1 =

Clears IRQ interrupt request (clears IRQF).

0 =

No effect.

IRQF — IRQ Interrupt Request Flag

Writing to the IRQF ﬂag bit will have no effect on it. If the additional setting of

IRQF ﬂag bit is not cleared in the IRQ service routine and the IRQE enable bit

remains set the CPU will re-enter the IRQ interrupt sequence continuously until

either the IRQF ﬂag bit or the IRQE enable bit is clear. The IRQF latch is

cleared by reset.

1 =

Indicates that an IRQ request is pending.

0 =

Indicates that no IRQ request triggered by pins PA0-3 or IRQ is

pending. The IRQF ﬂag bit can be cleared by writing a logic one to

the IRQR acknowledge bit to clear the IRQ latch and also

conditioning the external IRQ sources to be inactive (if the level

sensitive interrupts are enabled via mask option). Doing so before

exiting the service routine will mask out additional occurrences of

the IRQF.

IRQE — IRQ Interrupt Enable

The IRQE bit enables/disables the IRQF ﬂag bit to initiate an IRQ interrupt

sequence.

1 =

Enables IRQ interrupt, that is, the IRQF ﬂag bit can generate an

interrupt sequence. Reset sets the IRQE enable bit, thereby

enabling IRQ interrupts once the I-bit is cleared. Execution of the

STOP or WAIT instructions causes the IRQE bit to be set in order to

allow the external IRQ to exit these modes.

0 =

The IRQF ﬂag bit cannot generate an interrupt sequence.

4.5.3 Port A External Interrupts (PA0-PA3, by mask option)

The IRQ interrupt can also be triggered by the inputs on the PA0 to PA3 port pins

if enabled by a single mask option. If enabled, the lower four bits of Port A can

activate the IRQ interrupt function, and the interrupt operation will be the same as

for inputs to the IRQ pin. This mask option of PA0-3 interrupt allow all of these

input pins to be OR’ed with the input present on the IRQ pin. All PA0 to PA3 pins

must be selected as a group as an additional IRQ interrupt. All the PA0-3 interrupt

sources are also controlled by the IRQE enable bit.

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

68HC705JB3 데이터시트(PDF) 36 Page - Freescale Semiconductor, Inc

68HC705JB3 데이터시트(HTML) 36 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL