RX113 datasheet(64/131 Pages) RENESAS

64 / 131 page

R01DS0216EJ0120 Rev.1.20

Page 64 of 131

Sep 07, 2020

RX113 Group

5. Electrical Characteristics

Note 1. Current consumed only by the USB module.

Note 2. Includes the current supplied from the pull-up resistor of the USB0_DP pin to the pull-down resistor of the host device, in

addition to the current consumed by this MCU during the suspended state.

Note 3. Current consumed by the power supplies (VCC and VCC_USB).

Note 4. Current consumed only by the comparator B module.

Note 5. Current consumed only by the LCD module. Current when the LCD panel is not connected.

Note 6. Current consumed by the power supply (VCC).

Note 7. When VCC = AVCC0 = VCC_USB = 3.3 V.

Note 8. It does not include the current that flows through external divider resistors.

Note:

When powering on AVCC0 and VCC, power them on at the same time or VCC first.

Note 1. When OFS1.(STUPLVD1REN, FASTSTUP) = 11b.

Note 2. When OFS1.(STUPLVD1REN, FASTSTUP) = 10b.

Note 3. When OFS1.STUPLVD1REN = 0.

Note 4. Turn on the power supply voltage according to the normal startup rising gradient because the register settings set by OFS1 are

not read in boot mode.

USB operating

current*3

During USB communication operation under the

following settings and conditions

• Host controller operation is set to full-speed mode

Bulk OUT transfer (64 bytes) × 1,

bulk IN transfer (64 bytes) × 1

• Connect peripheral devices via a 1-meter USB

cable from the USB port.

IUSBH*1

—4.3

(VCC)

0.9

(VCC_USB)*3

—mA

During USB communication operation under the

following settings and conditions

• Function controller operation is set to full-speed

mode

Bulk OUT transfer (64 bytes) × 1,

bulk IN transfer (64 bytes) × 1

• Connect the host device via a 1-meter USB cable

from the USB port.

IUSBF*1

—3.6

(VCC)

1.1

(VCC_USB)*3

—mA

During suspended state under the following setting

and conditions

• Function controller operation is set to full-speed

mode (pull up the USB0_DP pin)

• Software standby mode

• Connect the host device via a 1-meter USB cable

from the USB port.

ISUSP*2

—0.35

(VCC)

170

(VCC_USB)*3

—µA

CTSU

operating

current

During measurement (CPU is in sleep mode)

Base clock: 2 MHz

Pin capacity: 50 pF

ICTSU

—

150

—

µA

Table 5.11

DC Characteristics (9)

Conditions: 1.8 V

≤ VCC = VCC_USB ≤ 3.6 V, 1.8 V ≤ AVCC0 ≤ 3.6 V, VSS = AVSS0 = VSS_USB = 0 V, T

a = –40 to +105°C

Item

Symbol

Min.

Typ.

Max.

Unit

Test Conditions

RAM standby voltage

VRAM

1.8

—

Table 5.12

DC Characteristics (10)

Conditions: 0 V

≤ VCC = VCC_USB ≤ 3.6 V, VSS = AVSS0 = VSS_USB = 0 V, T

a = –40 to +105°C

Item

Symbol

Min.

Typ.

Max.

Unit

Test Conditions

Power-on VCC

rising gradient

At normal startup*1

SrVCC

0.02

—

ms/V

During fast startup time*2

0.02

—

Voltage monitoring 1 reset enabled at startup

*3, *4

0.02

—

Table 5.10

DC Characteristics (8) (2/2)

Conditions: 1.8 V

≤ VCC = VCC_USB ≤ 3.6 V, 1.8 V ≤ AVCC0 ≤ 3.6 V, VSS = AVSS0 = VSS_USB = 0 V, T

a = –40 to +105°C

Item

Symbol

Min.

Typ.*7

Max.

Unit

Test

Conditions

RX113 데이터시트(PDF) 64 Page - Renesas Technology Corp

RX113 데이터시트(HTML) 64 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL