| 전자부품 데이터시트 검색엔진 |
|
LAN7430 데이터시트(PDF) 22 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
LAN7430 데이터시트(HTML) 22 Page - Microchip Technology |
|
22 / 77 page ![]() LAN7430/LAN7431 DS00002631D-page 22 2018-2019 Microchip Technology Inc. EEPROM Data In / Out EEDIO VIS / VO12 (PD) This bidirectional pin is used for the EEPROM data. This pin directly drives the data input of the external EEPROM. The data output of the external EEPROM drives this pin through an external resistor. Note: The internal pull-down holds a low on the pin during reset and provides a low on the input if an EEPROM is not connected. Note: An external resistor, on the EEPROM’s data output, must be used to prevent contention during data read operations. EEPROM Clock EECLK VO12 (PD) This pin drives the clock input of the external EEPROM. Note: The internal pull-down holds a low on the output pin during reset. Miscellaneous General Purpose I/O x GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 GPIO8 GPIO9 GPIO10 GPIO11 VIS/ VO8/ VOD8 (PU) Each of these general purpose I/O pins is fully program- mable as either a push-pull output, an open-drain output, or a Schmitt-triggered input with pull-up. Note: The pull-up is only enabled if the pin is set as a GPIO. Note: GPIO0 through GPIO3 are available for the LAN7430 and LAN7431. Note: GPIO4 through GPIO11 are available only for the LAN7431. Test Pin TEST VIS (PD) This pin is used to enable test modes and must be con- nected to ground for proper functional operation. System Reset RESET_N VIS System reset. This pin is active low. Note: If this signal is unused it must be pulled up to VDDVARIO. Indicator LEDs LED0 LED1 LED2 LED3 VOD12 VOS12 (LAN7430 only) LED signal sourced from Gigabit Ethernet PHY. Note: When enabled as LED outputs, the pins are either open-Drain or open-Source drivers. External PHY Bias Resistor ISET AI This pin should be connect to ground through a 6.04K 1% resistor. JTAG JTAG Test Mux Select TMS VIS JTAG test mode select. JTAG Test Clock TCK VIS JTAG test clock. Note: The maximum operating frequency of this clock is half of the system clock. JTAG Test Data Input TDI VIS JTAG data input JTAG Test Data Output TDO VO12 JTAG data output. TABLE 3-3: PIN DESCRIPTIONS (CONTINUED) Name Symbol Buffer Type Description |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |