STM32WB35CC datasheet(72/193 Pages) STMICROELECTRONICS

72 / 193 page

Pinouts and pin description

STM32WB55xx STM32WB35xx

72/193

DS11929 Rev 11

PA14

(JTCK-SWCLK)

I/O

(8)

JTCK-SWCLK, LPTIM1_OUT,

I2C1_SMBA, SAI1_FS_B,

CM4_EVENTOUT

PA15 (JTDI)

I/O

(8)

JTDI, TIM2_CH1, TIM2_ETR,

SPI1_NSS, CM4_EVENTOUT, MCO

PB3 (JTDO)

I/O

FT_a

JTDO-TRACESWO, TIM2_CH2,

SPI1_SCK, USART1_RTS_DE,

SAI1_SCK_B, CM4_EVENTOUT

COMP2_INM

PB4 (NJTRST)

I/O FT_fa

(8)

NJTRST, I2C3_SDA, SPI1_MISO,

USART1_CTS, SAI1_MCLK_B,

TIM17_BKIN, CM4_EVENTOUT

COMP2_INP

PB5

I/O

FT_a

LPTIM1_IN1, I2C1_SMBA,

SPI1_MOSI, USART1_CK,

LPUART1_TX, COMP2_OUT,

SAI1_SD_B, TIM16_BKIN,

CM4_EVENTOUT

PB6

I/O FT_fa

LPTIM1_ETR, I2C1_SCL,

USART1_TX, SAI1_FS_B,

TIM16_CH1N, MCO,

CM4_EVENTOUT

COMP2_INP

PB7

I/O FT_fa

LPTIM1_IN2, TIM1_BKIN, I2C1_SDA,

USART1_RX, TIM17_CH1N,

CM4_EVENTOUT

COMP2_INM, PVD_IN

VDD

1. PC14 and PC15 are supplied through the power switch. As this switch only sinks a limited amount of current (3 mA), the

use of the PC14 and PC15 GPIOs in output mode is limited:



- the speed must not exceed 2 MHz with a maximum load of 30 pF



- these GPIOs must not be used as current sources (e.g. to drive a LED).

2. After a Backup domain power-up, PC13, PC14 and PC15 operate as GPIOs. Their function then depends on the content of

the RTC registers that are not reset by the system reset. For details on how to manage these GPIOs, refer to the Backup

domain and RTC register descriptions in the reference manual RM0434, available on www.st.com.

3. The clock on LSCO is available in Run and Stop modes, and on PA2 in Standby and Shutdown modes.

4. RF pin, use the nominal PCB layout.

5. 32 MHz oscillator pins, use the nominal PCB layout according to reference design (see AN5165).

6. Reserved, must be kept unconnected.

7. High frequency (above 32 kHz) may impact the RF performance. Set output speed GPIOB_OSPEEDRy[1:0] to 00 (y = 0

and 1) during RF operation.

8. After reset these pins are configured as JTAG/SW debug alternate functions, and the internal pull-up on PA15, PA13 and

PB4 pins and the internal pull-down on PA14 pin are activated.

Table 17. STM32WB35xx pin and ball definitions (continued)

Alternate functions

Additional functions

Name (function

after reset)

STM32WB35CC 데이터시트(PDF) 72 Page - STMicroelectronics

STM32WB35CC 데이터시트(HTML) 72 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL