SPC58NH84C3 datasheet(130/147 Pages) STMICROELECTRONICS

130 / 147 page

Package information

SPC58EHx, SPC58NHx

130/147

DS12304 Rev 5

When the heat loss from the package case to the air does not factor into the calculation, the

junction temperature is predictable if the application board is similar to the thermal test

condition, with the component soldered to a board with internal planes.

The thermal resistance is expressed as the sum of a junction-to-case thermal resistance

plus a case-to-ambient thermal resistance:

Equation 3

RθJA = RθJC + RθCA

where:

RθJA = junction-to-ambient thermal resistance (°C/W)

RθJC = junction-to-case thermal resistance (°C/W)

RθCA = case to ambient thermal resistance (°C/W)

RθJC is device related and is not affected by other factors. The thermal environment can be

controlled to change the case-to-ambient thermal resistance, RθCA. For example, change

the air flow around the device, add a heat sink, change the mounting arrangement on the

printed circuit board, or change the thermal dissipation on the printed circuit board

surrounding the device. This description is most useful for packages with heat sinks where

90% of the heat flow is through the case to heat sink to ambient. For most packages, a

better model is required.

A more accurate two-resistor thermal model can be constructed from the junction-to-board

thermal resistance and the junction-to-case thermal resistance. The junction-to-case

thermal resistance describes when using a heat sink or where a substantial amount of heat

is dissipated from the top of the package. The junction-to-board thermal resistance

describes the thermal performance when most of the heat is conducted to the printed circuit

board. This model can be used to generate simple estimations and for computational fluid

dynamics (CFD) thermal models. More accurate compact Flotherm models can be

generated upon request.

To determine the junction temperature of the device in the application on a prototype board,

use the thermal characterization parameter (

ΨJT) to determine the junction temperature by

measuring the temperature at the top center of the package case using the following

equation:

Equation 4

TJ = TT + (ΨJT x PD)

where:

TT = thermocouple temperature on top of the package (°C)

ΨJT = thermal characterization parameter (°C/W)

PD = power dissipation in the package (W)

The thermal characterization parameter is measured in compliance with the JESD51-2

specification using a 40-gauge type T thermocouple epoxied to the top center of the

package case. Position the thermocouple so that the thermocouple junction rests on the

package. Place a small amount of epoxy on the thermocouple junction and approximately 1

mm of wire extending from the junction. Place the thermocouple wire flat against the

package case to avoid measurement errors caused by the cooling effects of the

thermocouple wire.

When board temperature is perfectly defined below the device, it is possible to use the

thermal characterization parameter (

ΨJPB) to determine the junction temperature by

SPC58NH84C3 데이터시트(PDF) 130 Page - STMicroelectronics

SPC58NH84C3 데이터시트(HTML) 130 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL