EM6821 datasheet(9/68 Pages) EMMICRO

9 / 68 page

EM6821

www.emmicroelectronic.com

4.1 Oscillation Detection Circuit

At power on, the voltage regulator starts to follow the supply voltage and triggers the power on reset circuitry,

and thus the system reset. The CPU of the EM6821 remains in the reset state for the ‘CPU Reset Delay’, to

allow the oscillator to stabilize after power up.

The oscillator is disabled during sleep mode. So when waking up from sleep mode, the CPU of the EM6821

remains in the reset state for the CPU Reset Delay, to allow the oscillator to stabilize. During this time, the

Oscillation Detection Circuit is inhibited.

In active or standby modes, the oscillator detection circuit monitors the oscillator. If it stops for any reason, a

system reset is generated. After clock restart the CPU waits for the CPU Reset Delay before executing the first

instructions.

The oscillation detection circuitry can be inhibited with bit NoOscWD = 1 in register RegVldCntl. At power up,

and after any system reset, the function is activated.

The ‘CPU Reset Delay’ is 32768 system clocks ( Ck[16] ) long.

4.2 Reset Terminal

During active or standby modes the Reset terminal has a debouncer to reject noise. Reset must therefore be

active for at least 16 ms (system clock = 32 KHz).

When canceling sleep mode, the debouncer is not active (no clock), however, reset passes through an

analogue filter with a time constant of typical. 5µs. In this case Reset pin must be high for at least 10 µs to

generate a system reset.

4.3 Input Port A Reset Function

By writing the OptInpRSel1 and OptInpRSel2 registers it is possible to choose any combination of port A input

values to execute a system reset. The reset condition must be valid for at least 16ms (system clock = 32kHz) in

active and standby mode.

OPTInpRSleep selects the input port A reset function in sleep mode. If set to "1" the occurrence of the selected

combination for input port A reset will immediately trigger a system reset (no debouncer) .

Reset combination selection (InpReset) is done with registers OptInpRSel1 and OptInpRSel2.

Following formula is applicable :

InpResPA = InpResPA[0] • InpResPA[1] • InpResPA[2] • InpResPA[3]

InpRes1PA[n] InpRes2PA[n] InpResPA[n]

VSS

PA[n]

not PA[n]

VDD

n = 0 to 3

i.e. ; - no reset if InpResPA[n] = VSS.

- Don't care function on a single bit with

its InpResPA[n] = VDD.

- Always Reset if InpResPA[3:0] = 'b1111

Figure 7. Input Port A Reset Structure

MUX

VSS

PA[3]

VDD

BIT

[0]

BIT

[1]

BIT

[2]

BIT

[3]

InpResPA

InpResPA[3]

InpRes2PA[3]

InpRes1PA[3]

Input Port A Reset

Bit[2] Selection

Input Port A Reset

Bit[1] Selection

Input Port A Reset

Bit[0] Selection

Input Port A Reset

Bit[3] Selection

Input

Reset

from

Port A

EM6821 데이터시트(PDF) 9 Page - EM Microelectronic - MARIN SA

EM6821 데이터시트(HTML) 9 Page - EM Microelectronic - MARIN SA

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

데이터시트 다운로드

링크 URL