 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
SC2000 데이터시트(PDF) 9 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
SC2000 데이터시트(HTML) 9 Page - NXP Semiconductors |
|
|
9 / 44 page  2000 Sep 07 9 Philips Semiconductors Preliminary specification Universal Timeslot Interchange SC2000 Reset (CS_7): Setting this bit to 1 forces the SC2000 into its reset state, and initializes all internal registers. This command reproduces the function of the RESET pin. Setting this bit to 0 returns the SC2000 to normal operation. This bit can be read back for verification purposes. Internal Registers The internal registers are accessed by reads and writes to the Data Registers using the address held in the Internal Address Register. Internal Register Memory Map Values for A_7 .. A_0 (H) Function R/W 00 . . 03 Configuration 1 . . Configuration 4 R/W 04 Version/Revision R/W 05 . . 7F Reserved . . Reserved R/W 80 . . 9F Destn Routing . . Destn Routing R/W A0 . . BF Source Routing . . Source Routing R/W C0 . . DF Destn Parallel . . Destn Parallel R/W E0 . . FF Source Parallel . . Source Parallel R/W Configuration Registers Configuration Register 1(00H) Global Output Enable (C_0): Clearing this bit to 0 forces all outputs to the high impedance state, with the exception of the microprocessor interface data bus. Setting this bit to 1 enables all outputs. This bit is cleared on RESET. Expansion Bus Timing Driver Enable (C_1): When SCbus Mode is selected (C_4 = 0), clearing this bit to 0 disables the expansion bus timing drivers. When PEB Resource Mode is selected (C_6, C_4 = 01), this bit has no effect. When PEB Network Mode is selected (C_6, C_4 = 11), clearing this bit to 0 disables the expansion bus drivers CLKR, L_CLKT, FSYNCR, L_FSYNCT, MSYNCR, and L_MSYNCT. Setting this bit to 1 enables these timing drivers. This bit is cleared on RESET. Framing Mode (C_3, C_2): This two-bit field selects the number of bits per frame (B/F), time slots per frame (TS/F) and frames per multi-frame (F/MF) on both the local and expansion bus. When SCbus Mode is selected (C_4 = 0), there is no multi-frame sync signal available on the expansion bus. The (00) combination of (C_3, C_2) is invalid. In this case the internal multi-frame sync will be free running, and synchronous to FSYNC. When PEB Mode is selected (C_4 = 1) the only valid combinations of (C_3, C_2) are (00) and (01). These bits are cleared on RESET. Expansion Bus Interface Select (C_4): This bit selects the expansion bus inter- face operating mode. Clearing this bit to 0 selects SCbus Mode. Setting this bit to 1 selects PEB Mode. This bit is cleared on RESET. Configuration Register 1 BIT Function 0 C_0: Global Output Enable 1 C_1: Expansion Bus Timing Driver Enable 2 3 C_2: Framing Mode 0 C_3:Framing Mode 1 4 C_4: Expansion Bus Interface Select 5 C_5: SCbus Loopback Mode 6 7 C_6: PEB module Type 0 C_7:PEB Module Type 1 Note: Bit 0 is the LSB of the Low Byte Data Register. Expansion Bus C_3, C_2 B/F TS/F F/MF 00 193 24 12 01 256 32 16 10 512 64 16 11 1024 128 16 Local Bus C_3, C_2 B/F TS/F F/MF 00 193 24 12 01 256 32 16 10 256 32 16 11 256 32 16 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
