| 전자부품 데이터시트 검색엔진 |
|
PM7366-PI 데이터시트(PDF) 112 Page - PMC-Sierra, Inc |
|
|
|||||||||||||||||||||||||||||
PM7366-PI 데이터시트(HTML) 112 Page - PMC-Sierra, Inc |
|
112 / 286 page ![]() RELEASED PM7366 FREEDM-8 DATA SHEET PMC-1970930 ISSUE 4 FRAME ENGINE AND DATA LINK MANAGER PROPRIETARY AND CONFIDENTIAL TO PMC-SIERRA,INC., AND FOR ITS CUSTOMERS’ INTERNAL USE 99 is set low, Big Endian format is selected. When LENDIAN is set high, Little Endian format is selected. Descriptor references and the contents of descriptors are always transferred in Little Endian Format. Please refer below for each format's byte ordering. Table 16 – Big Endian Format 00 Bit 31 24 23 16 15 8 7 Bit 0 DWORD Address 04 BYTE 0 BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 • • • • • • • • • • • • n-4 BYTE n-4 BYTE n-3 BYTE n-2 BYTE n-1 Table 17 – Little Endian Format 00 Bit 31 24 23 16 15 8 7 Bit 0 DWORD Address 04 BYTE 3 BYTE 2 BYTE 1 BYTE 0 BYTE 7 BYTE 6 BYTE 5 BYTE 4 • • • • • • • • • • • • n-4 BYTE n-1 BYTE n-2 BYTE n-3 BYTE n-4 SOE_E: The stop on error enable (SOE_E) bit determines the action the PCI controller will take when a system or parity error occurs. When set high the PCI controller will disconnect the PCI REQB signal from the PCI bus. This prevents the GPIC from the becoming a master device on the PCI bus in event of one of the following bits in the PCI Configuration Command/Status register being set: DPR, RTABT, MABT and SERR. When the SOE_E bit is set low the PCI controller will continue to allow master transactions on the PCI bus. Setting this bit low after an error has occurred or clearing the appropriate bit the PCI Configuration Command/Status register will reactivate the PCI REQB signal and allow the GPIC to resume servicing the local masters. In the event of a system or parity error it is recommended that the core device be reset unless the cause of the fault can be determined. PONS_E: The Report PERR on SERR enable (PONS_E) bit controls the source of system errors. When set high all parity errors will be signaled to the host via the SERRB output signal. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |