MPC8358E datasheet(39/96 Pages) FREESCALE

39 / 96 page

MPC8358E PowerQUICC™ II Pro Processor Revision 2.1 PBGA Silicon Hardware Specifications, Rev. 1

Freescale Semiconductor

Local Bus

Table 40 describes the general timing parameters of the local bus interface of the device.

Local bus clock to output high impedance for LAD/LDP

tLBKHOZ

—3.8

Notes:

1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state)

(reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1

symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes

high (H), in this case for clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to

go high (H), with respect to the output (O) going invalid (X) or output hold time.

2. All timings are in reference to rising edge of LSYNC_IN.

3. All signals are measured from OVDD/2 of the rising edge of LSYNC_IN to 0.4 × OVDD of the signal in question for 3.3-V

signaling levels.

4. Input timings are measured at the pin.

5.tLBOTOT1 should be used when RCWH[LALE] is not set and when the load on LALE output pin is at least 10pF less than

the load on LAD output pins.

6.tLBOTOT2 should be used when RCWH[LALE] is set and when the load on LALE output pin is at least 10pF less than the

load on LAD output pins.

7.tLBOTOT3 should be used when RCWH[LALE] is set and when the load on LALE output pin equals to the load on LAD output

pins.

8. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered

through the component pin is less than or equal to the leakage current specification.

Table 40. Local Bus General Timing Parameters—DLL Bypass Mode

Parameter

Symbol1

Min

Max

Unit

Notes

Local bus cycle time

tLBK

—

Input setup to local bus clock

tLBIVKH

7—

3, 4

Input hold from local bus clock

tLBIXKH

1.0

—

3, 4

LALE output fall to LAD output transition (LATCH hold time)

tLBOTOT1

1.5

—

LALE output fall to LAD output transition (LATCH hold time)

tLBOTOT2

3—

LALE output fall to LAD output transition (LATCH hold time)

tLBOTOT3

2.5

—

Local bus clock to output valid

tLBKHOV

—3

Table 39. Local Bus General Timing Parameters—DLL Enabled (continued)

Parameter

Symbol1

Min

Max

Unit

Notes

MPC8358E 데이터시트(PDF) 39 Page - Freescale Semiconductor, Inc

MPC8358E 데이터시트(HTML) 39 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

데이터시트 다운로드

링크 URL