E5ED/E5ED-B

32

E5ED-B (Push-In Plus Terminal Blocks)

Note: 1. The application of the terminals depends on the model.

2. Do not wire the terminals that are shown with a gray background.

3. When complying with EMC standards, the cable that connects the sensor must be 30 m or less.

If the cable length exceeds 30 m, compliance with EMC standards will not be possible.

4. Refer to E5

@D-B (Push-In Plus terminal block types) on page 48 for wire specifications and wiring methods.

5. Common terminals are indicated with asterisks (*).

You can use the input power supply and communications common terminals for crossover wiring.

Controllers given below if you use crossover wiring for the input power supply.

100 to 240 VAC Controllers: 16 max.

24 VAC/VDC Controllers: 8 max.

6. Due to UL Listing requirements, use the E54-CT1L or E54-CT3L Current Transformer with the factory wiring (internal wiring).

Use a UL category XOBA or XOBA7 current transformer that is UL Listed for field wiring (external wiring) and not the factory wiring (internal wiring).

27

28

26

17

29

30

31

32

19

20

18

21

22

23

24

25

43

44

42

33

45

46

47

48

35

36

34

37

38

39

40

41

RX

R

Q

OUT1

OUT1

QX

5

6

RR

R

OUT1

R

OUT2

R

OUT2

5

6

Q

OUT1

QR

C

OUT1

CX

5

6

1

2

3

4

1

2

3

4

32

Pt

A

B

B

mA

31

30

32

31

30

32

31

30

32

31

30

V

V

TC

I

11

12

9

10

2

1

7

8

5

6

3

4

13

14

15

16

9

10

11

12

13

14

15

16

*

5

6

7

8

5

6

7

8

Models with 1 Voltage

Output (for Driving SSR)

1 linear current

Output

Models with Voltage

Output (for Driving SSR)

and Relay Output

Models with 2

Relay Outputs

(2) Auxiliary Outputs

(1) Control output

Auxiliary outputs 1, 2, 3, 4

Auxiliary output 2

Auxiliary output 1

Auxiliary output 4

Auxiliary output 3

*

*

*

*

*

(no polarity)

(3) Input Power Supply

100 to 240 VAC

24 VAC/DC

(6) Options

(5) Sensor (Temperature/Analog) Input

The E5ED-B is set for a K-type thermocouple (input type =

5) by default. An input error (

s.err) will occur if the input

type setting does not agree with the temperature sensor.

Check the input type.

Relay output

Models with 4 auxiliary outputs

250 VAC, 2 A (resistive load)

E5ED-

@@ @ @ B M - @@@

↑

Terminal type

(1) (2) (3) (4) (5)

(6)

Relay output

250 VAC, 5 A

(resistive load)

Relay output

250 VAC, 5 A (resistive load)

Voltage output

(for driving SSR)

12 VDC, 40 mA

When There Is a Control Output 2: 21 mA

Linear current output

0 to 20 mA DC

4 to 20 mA DC

Load: 500 Ω max

Control output 1

Control output 2

Auxiliary outputs 1, 2, 3, 4

004

Communications,

2 event inputs

18

17

19

20

21

22

23

25

26

24

EV2

EV1

B(

+)

A

(

−)

RS-485

*

(

−)

(

−)

008

Communications, 2 event

inputs, and 1 CT input

18

17

19

20

21

22

23

25

26

24

CT1

EV2

EV1

B(

+)

A

(

−)

RS-485

(

−)

(

−)

010

4 event inputs, and 1 CT input

18

17

19

20

21

22

23

25

26

24

CT1

EV2

EV1

EV4

EV3

(

−)

(

−)

(

−)

(

−)

022

Communications, 4 event inputs,

and Transfer Output

V

I

18

17

19

20

21

22

23

25

26

24

EV2

EV1

B

(

+)

A

(

−)

RS-485

(

−)

(

−)

38

37

39

40

41

42

43

45

46

47

48

44

EV6

EV5

(

−)

(

−)

Transfer

Output

Models with

1 Relay Output

*

*

*

*

*

*

*

*

*

*

*

Use non-voltage inputs for the event inputs.

The polarity for a non-contact input is indicated by “(

−).”

+

−

+

−

+

−

+

−

−

+

−

+

+

+

−

Wiring Example:

To another E5ED-B

1

2

3

4