M32CSLASH8B datasheet(391/406 Pages) RENESAS

391 / 406 page

Under development

M32C/8B Group

25. Usage Notes

Preliminary specification

Specifications in this manual are tentative and subject to change.

REJ09B0450-0050 Rev.0.50 Oct 31, 2008

Page 374 of 385

25.9.2.3

Timer A (One-Shot Timer Mode)

• The TAiS bit (i = 0 to 4) in the TABSR register is set to 0 (count stops) after reset. Set the TAiS bit to 1

(count starts) after selecting timer operating mode and setting the TAi register.

• The following occurs when the TAiS bit in the TABSR register is set to 0 (count stops) while counting.

• The counter stops counting and the contents of the reload register is reloaded.

• The TAiOUT pin outputs a low-level (“L”) signal.

• The IR bit in the TAiIC register becomes 1 (interrupt requested) after one CPU clock cycle.

• One-shot timer is operated by an internal count source. When an external trigger is selected, a maximum of

one count source clock delay occurs between the trigger input to the TAiIN pin and the one-shot timer

output.

• The IR bit becomes 1 when one of the following procedures are used to set timer operating mode.

• When selecting one-shot timer mode after reset.

• When switching from timer mode to one-shot timer mode.

• When switching from event counter mode to one-shot timer mode.

To use the timer Ai interrupt (IR bit), set the IR bit to 0 after one of the above setting has done.

• When a retrigger occurs while counting, the contents of the reload register is reloaded after the counter

decrements by one, and continues counting.

To generate a retrigger while counting, wait 1 count source clock cycle or more after the last trigger

generation.

• When an external trigger input is used to start counting in timer A one-shot timer mode, do not provide an

external retrigger input for 300 ns before a timer A counter value reaches 0000h. The external retrigger may

be ignored.

(Technical update: TN-16C-125A/EA)

25.9.2.4

Timer A (Pulse Width Modulation Mode)

• The TAiS bit (i = 0 to 4) in the TABSR register is set to 0 (count stops) after reset. Set the TAiS bit to 1

(count starts) after selecting timer operating mode and setting the TAi register.

• The IR bit becomes 1 when one of the following procedures are used to set timer operating mode.

• When selecting PWM mode after reset.

• When switching from timer mode to PWM mode.

• When switching from event counter mode to PWM mode.

To use the timer Ai interrupt (IR bit), set the IR bit to 0 after one of the above setting has done.

• The following occurs when the TAiS bit is set to 0 (count stops) while PWM pulse is output.

• The counter stops.

• If the TAiOUT pin outputs a high-level (“H”) signal, the signal changes to “L” and the IR bit

becomes 1.

• If the TAiOUT pin outputs an “L” signal, its output signal and the IR bit remains unchanged.

M32C/8B 데이터시트(PDF) 391 Page - Renesas Technology Corp

M32C/8B 데이터시트(HTML) 391 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL