TL16C554, TL16C554I

ASYNCHRONOUS COMMUNICATIONS ELEMENT

SLLS165D – JANUARY 1994 – REVISED JULY 1998

4

POST OFFICE BOX 655303

TL16C550B

Circuitry

TL16C550B

Circuitry

TL16C550B

Circuitry

TL16C550B

Circuitry

Receive

Control

Logic

Transmit

Control

Logic

Modem

Control

Logic

Control

Logic

Data

Bus

Clock

Circuit

RXx

TXx

CTSx

RTSx

DSRx

DTRx

RIx

DCDx

D7 – D0

A2 – A0

CSx

IOR, IOW

RESET

XTAL1

XTAL2

INTx

TXRDY, RXRDY

Interrupt

Logic

8

† For TL16C550 circuitry, refer to the TL16C550B data sheet.

Terminal Functions

TERMINAL

NAME

FN

NO.

PN

NO.

I/O

DESCRIPTION

A0

A1

A2

34

33

32

48

47

46

I

Register select terminals. A0, A1, and A2 are three inputs used during read and write operations to

select the ACE register to read or write.

CSA, CSB,

CSC, CSD

16, 20,

50, 54

28, 33,

68, 73

I

Chip select. Each chip select (CSx) enables read and write operations to its respective channel.

CTSA, CTSB,

CTSC, CTSD

11, 25,

45, 59

23, 38,

63, 78

I

Clear to send. CTSx is a modem status signal. Its condition can be checked by reading bit 4 (CTS)

of the modem status register. CTS has no affect on the transmit or receive operation.

D7 – D0

66 – 68

1–5

15–11,

9–7

I/O

Data bus. Eight data lines with 3-state outputs provide a bidirectional path for data, control, and status

information between the TL16C554 and the CPU. D0 is the least significant bit (LSB).

DCDA, DCDB,

DCDC, DCDD

9, 27,

43, 61

19,42,

59, 2

I

Data carrier detect. A low on DCDx indicates the carrier has been detected by the modem. The

condition of this signal is checked by reading bit 7 of the modem status register.

DSRA, DSRB,

DSRC, DSRD

10, 26,

44, 60

22, 39,

62, 79

I

Data set ready. DSRx is a modem status signal. Its condition can be checked by reading bit 5 (DSR)

of the modem status register. DSR has no affect on the transmit or receive operation.

DTRA, DTRB,

DTRC, DTRD

12, 24,

46, 58

24, 37,

64, 77

O

Data terminal ready. DTRx is an output that indicates to a modem or data set that the ACE is ready

to establish communications. It is placed in the active state by setting the DTR bit of the modem

control register. DTRx is placed in the inactive state (high) either as a result of the master reset during

loop mode operation or clearing bit 0 (DTR) of the modem control register.

GND

6, 23,

40, 57

16, 36,

56, 76

Signal and power ground

INTN

65

6

I

Interrupt normal. INTN operates in conjunction with bit 3 of the modem status register and affects

operation of the interrupts (INTA, INTB, INTC, and INTD) for the four universal asynchronous

receiver/transceivers (UARTs) per the following table.

INTN

OPERATION OF INTERRUPTS

Brought low or

allowed to float

Interrupts are enabled according to the state of OUT2 (MCR bit 3). When the MCR

bit 3 is cleared, the 3-state interrupt output of that UART is in the high-impedance

state. When the MCR bit 3 is set, the interrupt output of the UART is enabled.

Brought high

Interrupts are always enabled, overriding the OUT2 enables.