 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
MFRC522 데이터시트(PDF) 23 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
MFRC522 데이터시트(HTML) 23 Page - NXP Semiconductors |
|
|
23 / 96 page  MFRC522_33 © NXP B.V. 2009. All rights reserved. Product data sheet PUBLIC Rev. 3 — 26 October 2009 112133 23 of 96 NXP Semiconductors MFRC522 Contactless reader IC 8.2 Analog interface and contactless UART 8.2.1 General The integrated contactless UART supports the external host online with framing and error checking of the protocol requirements up to 848 kBd. An external circuit can be connected to the communication interface pins MFIN and MFOUT to modulate and demodulate the data. The contactless UART handles the protocol requirements for the communication protocols in cooperation with the host. Protocol handling generates bit and byte-oriented framing. In addition, it handles error detection such as parity and CRC, based on the various supported contactless communication protocols. Remark: The size and tuning of the antenna and the power supply voltage have an important impact on the achievable operating distance. 8.2.2 TX p-driver The signal on pins TX1 and TX2 is the 13.56 MHz energy carrier modulated by an envelope signal. It can be used to drive an antenna directly using a few passive components for matching and filtering; see Section 15 on page 78. The signal on pins TX1 and TX2 can be configured using the TxControlReg register; see Section 9.3.2.5 on page 48. The modulation index can be set by adjusting the impedance of the drivers. The impedance of the p-driver can be configured using registers CWGsPReg and ModGsPReg. The impedance of the n-driver can be configured using the GsNReg register. The modulation index also depends on the antenna design and tuning. The TxModeReg and TxSelReg registers control the data rate and framing during transmission and the antenna driver setting to support the different requirements at the different modes and transfer speeds. [1] X = Do not care. Table 15. Register and bit settings controlling the signal on pin TX1 Bit Tx1RFEn Bit Force 100ASK Bit InvTx1RFOn Bit InvTx1RFOff Envelope Pin TX1 GSPMos GSNMos Remarks 0X[1] X[1] X[1] X[1] X[1] X[1] X[1] not specified if RF is switched off 10 0 X[1] 0 RF pMod nMod 100 % ASK: pin TX1 pulled to logic 0, independent of the InvTx1RFOff bit 1 RF pCW nCW 01 X[1] 0 RF pMod nMod 1 RF pCW nCW 11 X[1] 0 0 pMod nMod 1 RF_n pCW nCW |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
