P89LPC9211FDH datasheet(10/75 Pages) NXP

10 / 75 page

P89LPC92X1

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 2 — 1 December 2010

10 of 75

NXP Semiconductors

P89LPC9201/9211/922A1/9241/

8-bit microcontroller with 8-bit ADC

P0.6/CMP1/KBI6

I/O

P0.6 — Port 0 bit 6. High current source.

CMP1 — Comparator 1 output.

KBI6 — Keyboard input 6.

P0.7/T1/KBI7

I/O

P0.7 — Port 0 bit 7. High current source.

I/O

T1 — Timer/counter 1 external count input or overflow output.

KBI7 — Keyboard input 7.

P1.0 to P1.7

I/O, I

[1]

Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type, except for

three pins as noted below. During reset Port 1 latches are configured in the input

only mode with the internal pull-up disabled. The operation of the configurable

Port 1 pins as inputs and outputs depends upon the port configuration selected.

Each of the configurable port pins are programmed independently. Refer to

Section 7.16.1 “Port configurations” and Table 12 “Static characteristics” for

details. P1.2 to P1.3 are open drain when used as outputs. P1.5 is input only.

All pins have Schmitt trigger inputs.

Port 1 also provides various special functions as described below:

P1.0/TXD

I/O

P1.0 — Port 1 bit 0.

TXD — Transmitter output for serial port.

P1.1/RXD

I/O

P1.1 — Port 1 bit 1.

RXD — Receiver input for serial port.

P1.2/T0/SCL

I/O

P1.2 — Port 1 bit 2 (open-drain when used as output).

I/O

T0 — Timer/counter 0 external count input or overflow output (open-drain when

used as output).

I/O

SCL — I2C-bus serial clock input/output.

P1.3/INT0/SDA

I/O

P1.3 — Port 1 bit 3 (open-drain when used as output).

INT0 — External interrupt 0 input.

I/O

SDA — I2C-bus serial data input/output.

P1.4/INT1

8I/O

P1.4 — Port 1 bit 4. High current source.

INT1 — External interrupt 1 input.

P1.5/RST

P1.5 — Port 1 bit 5 (input only).

RST — External Reset input during power-on or if selected via UCFG1. When

functioning as a reset input, a LOW on this pin resets the microcontroller, causing

I/O ports and peripherals to take on their default states, and the processor begins

execution at address 0. Also used during a power-on sequence to force ISP mode.

P1.6

I/O

P1.6 — Port 1 bit 6. High current source.

P1.7

I/O

P1.7 — Port 1 bit 7. High current source.

P3.0 to P3.1

I/O

Port 3: Port 3 is a 2-bit I/O port with a user-configurable output type. During reset

Port 3 latches are configured in the input only mode with the internal pull-up

disabled. The operation of Port 3 pins as inputs and outputs depends upon the port

configuration selected. Each port pin is configured independently. Refer to Section

7.16.1 “Port configurations” and Table 12 “Static characteristics” for details.

All pins have Schmitt trigger inputs.

Port 3 also provides various special functions as described below:

Table 3.

Pin description …continued

Symbol

Type Description

TSSOP20,

DIP20

P89LPC9211FDH 데이터시트(PDF) 10 Page - NXP Semiconductors

P89LPC9211FDH 데이터시트(HTML) 10 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

데이터시트 다운로드

링크 URL