| 전자부품 데이터시트 검색엔진 |
|
MPC8544E 데이터시트(PDF) 97 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
MPC8544E 데이터시트(HTML) 97 Page - Freescale Semiconductor, Inc |
|
97 / 117 page ![]() MPC8544E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 5 Freescale Semiconductor 97 Thermal Table 71 provides the thermal resistance with heat sink in open flow. Simulations with heat sinks were done with the package mounted on the 2s2p thermal test board. The thermal interface material was a typical thermal grease such as Dow Corning 340 or Wakefield 120 grease. For system thermal modeling, the MPC8544E thermal model without a lid is shown in Figure 60. The substrate is modeled as a block 29 × 29 × 1.18 mm with an in-plane conductivity of 18.0 W/m•K and a through-plane conductivity of 1.0 W/m•K. The solder balls and air are modeled as a single block 29 × 29 × 0.58 mm with an in-plane conductivity of 0.034 W/m•K and a through plane conductivity of 12.1 W/m•K. The die is modeled as 7.6 × 8.4 mm with a thickness of 0.75 mm. The bump/underfill layer is modeled as a collapsed thermal resistance between the die and substrate assuming a conductivity of 6.5 W/m•K in the thickness dimension of 0.07 mm. The die is centered on the substrate. The thermal model uses approximate dimensions to reduce grid. Please refer to Figure 59 for actual dimensions. 20.2 Recommended Thermal Model Table 72 shows the MPC8544E thermal model. Table 71. Thermal Resistance with Heat Sink in Open Flow Heat Sink with Thermal Grease Air Flow Thermal Resistance ( °C/W) Wakefield 53 × 53 × 25 mm pin fin Natural convection 6.1 Wakefield 53 × 53 × 25 mm pin fin 1 m/s 3.0 Aavid 35 × 31 × 23 mm pin fin Natural convection 8.1 Aavid 35 × 31 × 23 mm pin fin 1 m/s 4.3 Aavid 30 × 30 × 9.4 mm pin fin Natural convection 11.6 Aavid 30 × 30 × 9.4 mm pin fin 1 m/s 6.7 Aavid 43 × 41 × 16.5 mm pin fin Natural convection 8.3 Aavid 43 × 41 × 16.5 mm pin fin 1 m/s 4.3 Table 72. MPC8544EThermal Model Conductivity Value Units Die (7.6 × 8.4 × 0.75mm) Silicon Temperature dependent — Bump/Underfill (7.6 × 8.4 × 0.070 mm) Collapsed Thermal Resistance Kz 6.5 W/m•K Substrate (29 × 29 × 1.18 mm) Kx 18 W/m•K Ky 18 Kz 1.0 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |