AFS090 datasheet(320/334 Pages) MICROSEMI

320 / 334 page

Datasheet Information

5- 4

R e v ision 2

v2.0, Revision 1

(continued)

The "Real-Time Counter (part of AB macro)" section was updated significantly.

Please review carefully.

2-35

There was a typo in Table 2-19 • Flash Memory Block Pin Names for the

ERASEPAGE description; it was the same as DISCARDPAGE. As as a result, the

ERASEPAGE description was updated.

2-42

The tFMAXCLKNVM parameter was updated in Table 2-25 • Flash Memory Block

Timing.

2-54

Table 2-31 • RAM4K9 and Table 2-32 • RAM512X18 were updated.

2-69

In Table 2-36 • Analog Block Pin Description, the Function description for PWRDWN

was changed from "Comparator power-down if 1"

"ADC comparator power-down if 1. When asserted, the ADC will stop functioning,

and the digital portion of the analog block will continue operating. This may result in

invalid status flags from the analog block. Therefore, Microsemi does not

recommend asserting the PWRDWN pin."

2-80

Figure 2-73 • Gate Driver Example was updated.

2-93

The "ADC Operation" section was updated. Please review carefully.

2-106

Figure 2-90 • Intra-Conversion Timing Diagram and Figure 2-91 • Injected

Conversion Timing Diagram are new.

2-115

The "Typical Performance Characteristics" section is new.

2-117

Table 2-49 • Analog Channel Specifications was significantly updated.

2-119

Table 2-50 • ADC Characteristics in Direct Input Mode was significantly updated.

2-122

In Table 2-52 • Calibrated Analog Channel Accuracy 1,2,3, note 2 was updated.

2-125

In Table 2-53 • Analog Channel Accuracy: Monitoring Standard Positive Voltages,

note 1 was updated.

2-126

In Table 2-54 • ACM Address Decode Table for Analog Quad, bit 89 was removed.

2-128

The data in the 2.5 V LCMOS and LVCMOS 2.5 V / 5.0 V rows were updated in

Table 2-75 • Fusion Standard and Advanced I/O – Hot-Swap and 5 V Input Tolerance

Capabilities.

2-145

In Table 2-78 • Fusion Standard I/O Standards—OUT_DRIVE Settings, LVCMOS

1.5 V, for OUT_DRIVE 2, was changed from a dash to a check mark.

2-154

The "VCC15A Analog Power Supply (1.5 V)" definition was changed from "A 1.5 V

analog power supply input should be used to provide this input"

"1.5 V clean analog power supply input for use by the 1.5 V portion of the analog

circuitry."

2-225

In the "VCC33PMP Analog Power Supply (3.3 V)" pin description, the following text

was changed from "VCC33PMP should be powered up before or simultaneously

with VCC33A"

"VCC33PMP should be powered up simultaneously with or after VCC33A."

2-225

The "VCCOSC Oscillator Power Supply (3.3 V)" section was updated to include

information about when to power the pin.

2-225

Revision

Changes

Page

AFS090 데이터시트(PDF) 320 Page - Microsemi Corporation

AFS090 데이터시트(HTML) 320 Page - Microsemi Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL