AFS090 datasheet(324/334 Pages) MICROSEMI

324 / 334 page

Datasheet Information

5- 8

R e v ision 2

Advance 1.0

(continued)

In the "Gate Driver" section, 25 mA was changed to 20 mA and 1.5 MHz was

changed to 1.3 MHz. In addition, the following sentence was deleted:

The maximum AG pad switching frequency is 1.25 MHz.

2-94

The "Temperature Monitor" section was updated to rewrite most of the text and add

Figure 2-78, Figure 2-79, and Table 2-38 • Temperature Data Format.

2-96

In Table 2-38 • Temperature Data Format, the temperature K column was changed

for 85°C from 538 to 358.

2-98

In Table 2-45 • ADC Interface Timing, "Typical-Case" was changed to "Worst-Case."

2-110

The "ADC Interface Timing" section is new.

2-110

Table 2-46 • Analog Channel Specifications was updated.

2-118

The "VCC15A Analog Power Supply (1.5 V)" section was updated.

2-224

The "VCCPLA/B PLL Supply Voltage" section is new.

2-225

In "VCCNVM Flash Memory Block Power Supply (1.5 V)" section, supply was

changed to supply input.

2-224

The "VCCPLA/B PLL Supply Voltage" pin description was updated to include the

following statement:

Actel recommends tying VCCPLX to VCC and using proper filtering circuits to

decouple VCC noise from PLL.

2-225

The "VCOMPLA/B Ground for West and East PLL" section was updated.

2-225

In Table 2-47 • ADC Characteristics in Direct Input Mode, the commercial conditions

were updated and note 2 is new.

2-121

The VCC33ACAP signal name was changed to "XTAL1 Crystal Oscillator Circuit

Input".

2-228

Table 2-48 • Uncalibrated Analog Channel Accuracy* is new.

2-123

Table 2-49 • Calibrated Analog Channel Accuracy 1,2,3 is new.

2-124

Table 2-50 • Analog Channel Accuracy: Monitoring Standard Positive Voltages is

new.

2-125

In Table 2-57 • Voltage Polarity Control Truth Table—AV (x = 0), AC (x = 1), and AT

(x = 3)*, the following I/O Bank names were changed:

Hot-Swap changed to Standard

LVDS changed to Advanced

2-131

In Table 2-58 • Prescaler Op Amp Power-Down Truth Table—AV (x = 0), AC (x = 1),

and AT (x = 3), the following I/O Bank names were changed:

Hot-Swap changed to Standard

LVDS changed to Advanced

2-132

In the title of Table 2-64 • I/O Standards Supported by Bank Type, LVDS I/O was

changed to Advanced I/O.

2-134

The title was changed from "Fusion Standard, LVDS, and Standard plus Hot-Swap

I/O" to Table 2-68 • Fusion Standard and Advanced I/O Features. In addition, the

table headings were all updated. The heading used to be Standard and LVDS I/O

and was changed to Advanced I/O. Standard Hot-Swap was changed to just

Standard.

2-136

Revision

Changes

Page

AFS090 데이터시트(PDF) 324 Page - Microsemi Corporation

AFS090 데이터시트(HTML) 324 Page - Microsemi Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL