| 전자부품 데이터시트 검색엔진 |
|
MC34708 데이터시트(PDF) 16 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
MC34708 데이터시트(HTML) 16 Page - Freescale Semiconductor, Inc |
|
16 / 159 page ![]() Analog Integrated Circuit Device Data Freescale Semiconductor 16 MC34708 General Product Characteristics 5.2.1 Power Dissipation During operation, the temperature of the die should not exceed the maximum junction temperature. To optimize the thermal management scheme and avoid overheating, the MC34708 PMIC provides a thermal management system. The thermal protection is based on a circuit with a voltage output proportional to the absolute temperature.This voltage can be read out via the ADC for specific temperature readouts, see Channel 3 Die Temperature. The ADEN SPI bit must be set = 1 to enable the comparators for the thermal monitoring (THERM110, THERM120, THERM125, THERM130, and thermal shutdown). With ADEN = 0 the thermal monitors and thermal shutdown are disabled. Interrupts THERM110, THERM120, THERM125, and THERM130 will be generated when respectively crossing in either direction the thresholds specified in Table 6. The temperature range can be determined by reading the THERMxxxS bits. Thermal protection is integrated to power off the MC34708 PMIC and disables the charger circuitry in case of over dissipation. This thermal protection will act above the maximum junction temperature to avoid any unwanted power downs. The protection is debounced for 8.0 ms in order to suppress any (thermal) noise. This protection should be considered as a fail-safe mechanism and therefore the application design should be dimensioned such that this protection is not tripped under normal conditions. The temperature thresholds and the sense bit assignment are listed in Table 6 . The THERM1xx thresholds are debounced by the SPI bits DIE_TEMP_DB[1:0], which are programmable from 100 s to 4.0 ms (4.0 ms by default), see Table 7. When the die temperature crosses these thresholds, the corresponding sense bit will change and an interrupt will be generated to notify the software that the hardware is reaching its thermal limit. Table 6. Thermal Protection Thresholds Parameter Min Typ Max Units Notes Thermal 110 °C threshold (THERM110) 105 110 115 °C Thermal 120 °C threshold (THERM120) 115 120 125 °C Thermal 125 °C threshold (THERM125) 120 125 130 °C Thermal 130 °C threshold (THERM130) 125 130 135 °C Thermal warning hysteresis 2.0 - 4.0 °C (12) Thermal protection threshold 130 140 150 °C Notes 12. Equivalent to approx. 30 mW min, 60 mW max Table 7. Die Temp Debounce Settings DIE_TEMP_DB [1:0] Time Units 00 0.100 ms 01 1.0 ms 10 2.5 ms 11 (default) 4.0 ms |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |