PIC16F882-ISLASHSS datasheet(33/338 Pages) MICROCHIP

33 / 338 page

 2006-2012 Microchip Technology Inc.

DS41291G-page 33

PIC16F882/883/884/886/887

2.2.2.3

INTCON Register

The INTCON register, shown in Register 2-3, is a

readable and writable register, which contains the various

enable and flag bits for TMR0 register overflow, PORTB

change and external INT pin interrupts.

Note:

Interrupt flag bits are set when an interrupt

condition occurs, regardless of the state of

its corresponding enable bit or the Global

Enable bit, GIE of the INTCON register.

User

software

should

ensure

the

appropriate interrupt flag bits are clear

prior to enabling an interrupt.

INTCON: INTERRUPT CONTROL REGISTER

R/W-0

R/W-x

GIE

PEIE

T0IE

INTE

RBIE(1)

T0IF(2)

INTF

RBIF

bit 7

bit 0

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 7

GIE: Global Interrupt Enable bit

1 = Enables all unmasked interrupts

0 = Disables all interrupts

bit 6

PEIE: Peripheral Interrupt Enable bit

1 = Enables all unmasked peripheral interrupts

0 = Disables all peripheral interrupts

bit 5

T0IE: Timer0 Overflow Interrupt Enable bit

1 = Enables the Timer0 interrupt

0 = Disables the Timer0 interrupt

bit 4

INTE: INT External Interrupt Enable bit

1 = Enables the INT external interrupt

0 = Disables the INT external interrupt

bit 3

RBIE: PORTB Change Interrupt Enable bit(1)

1 = Enables the PORTB change interrupt

0 = Disables the PORTB change interrupt

bit 2

T0IF: Timer0 Overflow Interrupt Flag bit(2)

1 = TMR0 register has overflowed (must be cleared in software)

0 = TMR0 register did not overflow

bit 1

INTF: INT External Interrupt Flag bit

1 = The INT external interrupt occurred (must be cleared in software)

0 = The INT external interrupt did not occur

bit 0

RBIF: PORTB Change Interrupt Flag bit

1 = When at least one of the PORTB general purpose I/O pins changed state (must be cleared in software)

0 = None of the PORTB general purpose I/O pins have changed state

Note 1:

IOCB register must also be enabled.

T0IF bit is set when Timer0 rolls over. Timer0 is unchanged on Reset and should be initialized before clearing

T0IF bit.

PIC16F882-I/SS 데이터시트(PDF) 33 Page - Microchip Technology

PIC16F882-I/SS 데이터시트(HTML) 33 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL