PIC16F883-ESLASHSO. datasheet(231/338 Pages) MICROCHIP

231 / 338 page

 2006-2012 Microchip Technology Inc.

DS41291G-page 231

PIC16F882/883/884/886/887

FIGURE 14-10:

WAKE-UP FROM SLEEP THROUGH INTERRUPT

14.7

Code Protection

If the code protection bit(s) have not been

programmed, the on-chip program memory can be

read out using ICSP™ for verification purposes.

14.8

ID Locations

Four memory locations (2000h-2003h) are designated

as ID locations where the user can store checksum or

other code identification numbers. These locations are

not accessible during normal execution but are readable

and writable during Program/Verify mode. Only the

Least Significant 7 bits of the ID locations are used.

14.9

In-Circuit Serial Programming™

The PIC16F882/883/884/886/887 microcontrollers can

be serially programmed while in the end application cir-

cuit. This is simply done with two lines for clock and

data and three other lines for:

•power

• ground

• programming voltage

This allows customers to manufacture boards with

unprogrammed devices and then program the micro-

controller just before shipping the product. This also

allows the most recent firmware or a custom firmware

to be programmed.

The device is placed into a Program/Verify mode by

holding the RB6/ICSPCLK and RB7/ICSPDAT pins low,

while raising the MCLR (VPP) pin from VIL to VIHH. See

the “PIC16F88X Memory Programming Specification”

(DS41287) for more information. RB7 becomes the

programming data and RB6 becomes the programming

clock. Both RB7 and RB6 are Schmitt Trigger inputs in

this mode.

After Reset, to place the device into Program/Verify

mode, the Program Counter (PC) is at location 00h. A

6-bit command is then supplied to the device.

Depending on the command, 14 bits of program data

are then supplied to or from the device, depending on

whether the command was a Load or a Read. For

complete details of serial programming, please refer to

the “PIC16F88X Memory Programming Specification”

(DS41287).

A typical In-Circuit Serial Programming connection is

shown in Figure 14-11.

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

OSC1

CLKOUT(4)

INT pin

INTF flag

(INTCON<1>)

GIE bit

(INTCON<7>)

Instruction Flow

Instruction

Fetched

Instruction

Executed

PC + 1

PC + 2

Inst(PC) = Sleep

Inst(PC – 1)

Inst(PC + 1)

Sleep

Processor in

Sleep

Interrupt Latency(3)

Inst(PC + 2)

Inst(PC + 1)

Inst(0004h)

Inst(0005h)

Inst(0004h)

Dummy Cycle

PC + 2

0004h

0005h

Dummy Cycle

TOST(2)

PC + 2

Note 1:

XT, HS or LP Oscillator mode assumed.

TOST = 1024 TOSC (drawing not to scale). This delay does not apply to EC and RC Oscillator modes.

GIE = 1 assumed. In this case after wake-up, the processor jumps to 0004h. If GIE = 0, execution will continue in-line.

CLKOUT is not available in XT, HS, LP or EC Oscillator modes, but shown here for timing reference.

Note:

The entire data EEPROM and Flash

program memory will be erased when the

code protection is switched from on to off.

See

the

“PIC16F88X

Memory

Programming Specification” (DS41287) for

more information.

PIC16F883-E/SO. 데이터시트(PDF) 231 Page - Microchip Technology

PIC16F883-E/SO. 데이터시트(HTML) 231 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL