PIC16F883-ESLASHSO. datasheet(175/338 Pages) MICROCHIP

175 / 338 page

 2006-2012 Microchip Technology Inc.

DS41291G-page 175

PIC16F882/883/884/886/887

12.4

EUSART Synchronous Mode

Synchronous serial communications are typically used

in systems with a single master and one or more

slaves. The master device contains the necessary

circuitry for baud rate generation and supplies the clock

for all devices in the system. Slave devices can take

advantage of the master clock by eliminating the

internal clock generation circuitry.

There are two signal lines in Synchronous mode: a bidi-

rectional data line and a clock line. Slaves use the

external clock supplied by the master to shift the serial

data into and out of their respective receive and trans-

mit shift registers. Since the data line is bidirectional,

synchronous operation is half-duplex only. Half-duplex

refers to the fact that master and slave devices can

receive and transmit data but not both simultaneously.

The EUSART can operate as either a master or slave

device.

Start and Stop bits are not used in synchronous

transmissions.

12.4.1

SYNCHRONOUS MASTER MODE

The following bits are used to configure the EUSART

for Synchronous Master operation:

• SYNC = 1

• CSRC = 1

• SREN = 0 (for transmit); SREN = 1 (for receive)

• CREN = 0 (for transmit); CREN = 1 (for receive)

• SPEN = 1

Setting the SYNC bit of the TXSTA register configures

the device for synchronous operation. Setting the CSRC

bit of the TXSTA register configures the device as a

master. Clearing the SREN and CREN bits of the RCSTA

otherwise the device will be configured to receive. Setting

the SPEN bit of the RCSTA register enables the

EUSART. If the RX/DT or TX/CK pins are shared with an

analog peripheral the analog I/O functions must be

disabled by clearing the corresponding ANSEL bits.

12.4.1.1

Master Clock

Synchronous data transfers use a separate clock line,

which is synchronous with the data. A device config-

ured as a master transmits the clock on the TX/CK line.

The TX/CK pin output driver is automatically enabled

when the EUSART is configured for synchronous

transmit or receive operation. Serial data bits change

on the leading edge to ensure they are valid at the trail-

ing edge of each clock. One clock cycle is generated

for each data bit. Only as many clock cycles are

generated as there are data bits.

12.4.1.2

Clock Polarity

A clock polarity option is provided for Microwire

compatibility. Clock polarity is selected with the SCKP

bit of the BAUDCTL register. Setting the SCKP bit sets

the clock Idle state as high. When the SCKP bit is set,

the data changes on the falling edge of each clock.

Clearing the SCKP bit sets the Idle state as low. When

the SCKP bit is cleared, the data changes on the rising

edge of each clock.

12.4.1.3

Synchronous Master Transmission

Data is transferred out of the device on the RX/DT pin.

The RX/DT and TX/CK pin output drivers are automat-

ically enabled when the EUSART is configured for

synchronous master transmit operation.

A transmission is initiated by writing a character to the

TXREG register. If the TSR still contains all or part of a

previous character the new character data is held in the

TXREG until the last bit of the previous character has

been transmitted. If this is the first character, or the

previous character has been completely flushed from

the TSR, the data in the TXREG is immediately trans-

ferred to the TSR. The transmission of the character

commences immediately following the transfer of the

data to the TSR from the TXREG.

Each data bit changes on the leading edge of the

master clock and remains valid until the subsequent

leading clock edge.

12.4.1.4

Synchronous Master Transmission

Setup:

Initialize the SPBRGH, SPBRG register pair and

the BRGH and BRG16 bits to achieve the

desired baud rate (see Section 12.3 “EUSART

Baud Rate Generator (BRG)”).

Enable the synchronous master serial port by

setting bits SYNC, SPEN, and CSRC.

Disable Receive mode by clearing bits SREN

and CREN.

Enable Transmit mode by setting the TXEN bit.

If 9-bit transmission is desired, set the TX9 bit.

If interrupts are desired, set the TXIE bit of the

PIE1 register and the GIE and PEIE bits of the

INTCON register.

If 9-bit transmission is selected, the ninth bit

should be loaded in the TX9D bit.

Start transmission by loading data to the TXREG

Note:

The TSR register is not mapped in data

memory, so it is not available to the user.

PIC16F883-E/SO. 데이터시트(PDF) 175 Page - Microchip Technology

PIC16F883-E/SO. 데이터시트(HTML) 175 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL