LAN8720AI datasheet(63/79 Pages) SMSC

63 / 79 page

Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support

Datasheet

SMSC LAN8720A/LAN8720Ai

Revision 1.4 (08-23-12)

DATASHEET

Chapter 5 Operational Characteristics

5.1

Absolute Maximum Ratings*

Supply Voltage (VDDIO, VDD1A, VDD2A) (Note 5.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +3.6V

Digital Core Supply Voltage (VDDCR) (Note 5.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +1.5V

Ethernet Magnetics Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +3.6V

Positive voltage on signal pins, with respect to ground (Note 5.2) . . . . . . . . . . . . . . . . . . . . . . . . . . +6V

Negative voltage on signal pins, with respect to ground (Note 5.3) . . . . . . . . . . . . . . . . . . . . . . . . -0.5V

Positive voltage on XTAL1/CLKIN, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V

Positive voltage on XTAL2, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V

Ambient Operating Temperature in Still Air (TA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note 5.40

Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55oC to +150oC

Junction to Ambient (

JA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59.8

oC/W

Junction to Case (

JC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12.6

oC/W

Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020

HBM ESD Performance per JEDEC JESD22-A114. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Class 3A

IEC61000-4-2 Contact Discharge ESD Performance (Note 5.5) . . . . . . . . . . . . . . . . . . . . . . . . . .+/-8kV

IEC61000-4-2 Air-Gap Discharge ESD Performance (Note 5.5) . . . . . . . . . . . . . . . . . . . . . . . . .+/-15kV

Latch-up Performance per EIA/JESD 78 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+/-150mA

Note 5.1

When powering this device from laboratory or system power supplies, it is important that

the absolute maximum ratings not be exceeded or device failure can result. Some power

supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In

addition, voltage transients on the AC power line may appear on the DC output. If this

possibility exists, it is suggested that a clamp circuit be used.

Note 5.2

This rating does not apply to the following pins: XTAL1/CLKIN, XTAL2, RBIAS.

Note 5.3

This rating does not apply to the following pins: RBIAS.

Note 5.4

0oC to +85oC for extended commercial version, -40oC to +85oC for industrial version.

Note 5.5

Performed by independent 3rd party test facility.

*Stresses exceeding those listed in this section could cause permanent damage to the device. This is

a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect

device reliability. Functional operation of the device at any condition exceeding those indicated in

Section 5.2, "Operating Conditions**", Section 5.1, "Absolute Maximum Ratings*", or any other

applicable section of this specification is not implied. Note, device signals are NOT 5 volt tolerant

unless specified otherwise.

LAN8720AI 데이터시트(PDF) 63 Page - SMSC Corporation

LAN8720AI 데이터시트(HTML) 63 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

데이터시트 다운로드

링크 URL