30F4013 datasheet(63/228 Pages) MICROCHIP

63 / 228 page

 2010 Microchip Technology Inc.

DS70138G-page 63

dsPIC30F3014/4013

Each hard trap that occurs must be Acknowledged

before code execution of any type may continue. If a

lower priority hard trap occurs while a higher priority

trap is pending, Acknowledged, or is being processed,

a hard trap conflict occurs.

The device is automatically Reset in a hard trap conflict

condition. The TRAPR status bit (RCON<15>) is set

when the Reset occurs so that the condition may be

detected in software.

FIGURE 8-1:

TRAP VECTORS

8.4

Interrupt Sequence

All interrupt event flags are sampled in the beginning of

each instruction cycle by the IFSx registers. A pending

Interrupt Request (IRQ) is indicated by the flag bit

being equal to a ‘1’ in an IFSx register. The IRQ causes

an interrupt to occur if the corresponding bit in the Inter-

rupt Enable (IECx) register is set. For the remainder of

the instruction cycle, the priorities of all pending

interrupt requests are evaluated.

If there is a pending IRQ with a priority level greater

than the current processor priority level in the IPL bits,

the processor is interrupted.

The processor then stacks the current program counter

and the low byte of the processor STATUS register

(SRL), as shown in Figure 8-2. The low byte of the

STATUS register contains the processor priority level at

the time prior to the beginning of the interrupt cycle.

The processor then loads the priority level for this

interrupt into the STATUS register. This action disables

all lower priority interrupts until the completion of the

Interrupt Service Routine.

FIGURE 8-2:

INTERRUPT STACK FRAME

The RETFIE (return from interrupt) instruction unstacks

the program counter and STATUS registers to return

the processor to its state prior to the interrupt

sequence.

Address Error Trap Vector

Oscillator Fail Trap Vector

Stack Error Trap Vector

Reserved Vector

Math Error Trap Vector

Reserved

Oscillator Fail Trap Vector

Address Error Trap Vector

Reserved Vector

Interrupt 0 Vector

Interrupt 1 Vector

—

Interrupt 52 Vector

Interrupt 53 Vector

Math Error Trap Vector

0x000000

0x000014

Reserved

Stack Error Trap Vector

Reserved Vector

Interrupt 1 Vector

—

Interrupt 52 Vector

Interrupt 53 Vector

IVT

AIVT

0x000080

0x00007E

0x0000FE

Reserved

0x000094

Reset – GOTO Instruction

Reset – GOTO Address

0x000002

Reserved

0x000082

0x000084

0x000004

Reserved Vector

Interrupt 0 Vector

—

Note 1: The user can always lower the priority

level by writing a new value into SR. The

Interrupt Service Routine must clear the

interrupt flag bits in the IFSx register

before lowering the processor interrupt

priority, in order to avoid recursive

interrupts.

2: The IPL3 bit (CORCON<3>) is always

clear when interrupts are being pro-

cessed. It is set only during execution of

traps.

W15 (before CALL)

W15 (after CALL)

0x0000

PC<15:0>

SRL IPL3 PC<22:16>

POP : [--W15]

PUSH : [W15++]

30F4013 데이터시트(PDF) 63 Page - Microchip Technology

30F4013 데이터시트(HTML) 63 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL