| 전자부품 데이터시트 검색엔진 |
|
DM163006 데이터시트(PDF) 45 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
DM163006 데이터시트(HTML) 45 Page - Microchip Technology |
|
45 / 320 page ![]() 2001 Microchip Technology Inc. Advance Information DS39541A-page 45 PIC18C601/801 4.2.3 PUSH AND POP INSTRUCTIONS Since the Top-of-Stack (TOS) is readable and writable, the ability to push values onto the stack and pop values off the stack, without disturbing normal program execu- tion, is a desirable option. To push the current PC value onto the stack, a PUSH instruction can be executed. This will increment the stack pointer and load the cur- rent PC value onto the stack. TOSU, TOSH and TOSL can then be modified to place a return address on the stack. The POP instruction discards the current TOS by decre- menting the stack pointer. The previous value pushed onto the stack then becomes the TOS value. 4.2.4 STACK FULL/UNDERFLOW RESETS These RESETS are enabled/disabled by programming the STVREN configuration bit in CONFIG4L register. When the STVREN bit is disabled, a full or underflow condition will set the appropriate STKFUL or STKUNF bit, but not cause a RESET. When the STVREN bit is enabled, a full or underflow will set the appropriate STKFUL or STKUNF bit and then cause a RESET. The STKFUL or STKUNF bits are only cleared by the user software or a POR. 4.3 Fast Register Stack A “fast return” option is available for interrupts and calls. A fast register stack is provided for the STATUS, WREG and BSR registers, and is only one layer in depth. The stack is not readable or writable and is loaded with the current value of the corresponding register when the processor vectors for an interrupt. The values in the fast register stack are then loaded back into the working reg- isters, if the fast return instruction is used to return from the interrupt. A low or high priority interrupt source will push values into the stack registers. If both low and high priority interrupts are enabled, the stack registers cannot be used reliably for low priority interrupts. If a high priority interrupt occurs while servicing a low priority interrupt, the stack register values stored by the low priority interrupt will be overwritten. If high priority interrupts are not disabled during low pri- ority interrupts, users must save the key registers in software during a low priority interrupt. If no interrupts are used, the fast register stack can be used to restore the STATUS, WREG and BSR registers at the end of a subroutine call. To use the fast register stack for a subroutine call, a fast call instruction must be executed. Example 4-1 shows a source code example that uses the fast register stack. EXAMPLE 4-1: FAST REGISTER STACK CODE EXAMPLE CALL SUB1, FAST ;STATUS, WREG, BSR ;SAVED IN FAST REGISTER ;STACK • • SUB1 • • • RETURN FAST ;RESTORE VALUES SAVED ;IN FAST REGISTER STACK |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |