AM186 datasheet(30/112 Pages) AMD

30 / 112 page

Am186TMER and Am188TMER Microcontrollers Data Sheet

DRAF

PIN DESCRIPTIONS

Pins Used by Emulators

The following pins are used by emulators: A19–A0,

AO15–AO8, AD7–AD0, ALE, BHE/ADEN (on the

Am186ER microcontroller), CLKOUTA, RFSH2/ADEN

(on the Am188ER microcontroller), RD, S2, S1/IMDIS,

S0/SREN, S6/CLKSEL1, and UZI/CLKSEL2.

Emu la to rs re qu ire th at S6/C LKSEL1 and UZI /

CLKSEL2 be configured in their normal functionality,

that is, as S6 and UZI. If BHE/ADEN (on the Am186ER

microcontroller) or RFSH2/ADEN (on the Am188ER

microcontroller) is held Low during the rising edge of

RES, S6 and UZI are configured in their normal func-

tionality and cannot be programmed as PIOs.

A19–A0

(A19/PIO9, A18/PIO8, A17/PIO7)

Address Bus (output, three-state, synchronous)

These pins supply nonmultiplexed memory or I/O ad-

dresses to the system one-half of a CLKOUTA period

earlier than the multiplexed address and data bus

(AD15–AD0 on the Am186ER microcontroller or

AO15–AO8 and AD7–AD0 on the Am188ER microcon-

troller). During a bus hold or reset condition, the ad-

dress bus is in a high-impedance state.

AD7–AD0

Address and Data Bus (input/output, three-state,

synchronous, level-sensitive)

These time-multiplexed pins supply partial memory or

I/O addresses, as well as data, to the system. AD7–

AD0 supply the low-order 8 bits of an address to the

system during the first period of a bus cycle (t1). On a

write, these pins supply data to the system during the

remaining periods of that cycle (t2, t3, and t4). On a

read, these pins latch data at the end of t3.

Also, if S0/SREN (show read enable) was pulled Low

during reset or if the SR bit is set in the Internal Memory

Chip Select (IMCS) Register, these pins supply the

data read from internal memory during t3 and t4.

On the Am186ER microcontroller, AD7–AD0 combine

with AD15–AD8 to form a complete multiplexed ad-

dress and 16-bit data bus.

On the Am188ER microcontroller, AD7–AD0 combine

with AO15–AO8 to form a complete multiplexed ad-

dress bus while AD7–AD0 is the 8-bit data bus.

The address phase of these pins can be disabled. See

the ADEN description with the BHE/ADEN pin. When

WLB is negated, these pins are three-stated during t2,

t3, and t4.

During a bus hold or reset condition, the address and

data bus are in a high-impedance state.

During a power-on reset, the address and data bus

pins (AD15–AD0 for the Am186ER microcontroller,

AO15–AO8 and AD7–AD0 for the Am188ER microcon-

troller) can also be used to load system configuration

information into the internal reset configuration regis-

ter. The system information is latched on the rising

edge of RES.

AD15–AD8 (Am186™ER Microcontroller)

Address and Data Bus (input/output, three-state,

synchronous, level-sensitive)

These time-multiplexed pins supply partial memory or

I/O addresses, as well as data, to the system. AD15–

AD8 supply the high-order 8 bits of an address to the

system during the first period of a bus cycle (t1). On a

write, these pins supply data to the system during the

remaining periods of that cycle (t2, t3, and t4). On a

read, these pins latch data at the end of t3.

Also, if S0/SREN (show read enable) was pulled Low

during reset or if the SR bit is set in the Internal Memory

Chip Select (IMCS) Register, these pins supply the

data read from internal memory during t3 and t4.

On the Am186ER microcontroller, AD15–AD8 combine

with AD7–AD0 to form a complete multiplexed address

and 16-bit data bus.

The address phase of these pins can be disabled. See

the ADEN description with the BHE/ADEN pin. When

WHB is negated, these pins are three-stated during t2,

t3, and t4.

During a bus hold or reset condition, the address and

data bus is in a high-impedance state.

During a power-on reset, the address and data bus

pins (AD15–AD0 for the Am186ER microcontroller,

AO15–AO8 and AD7–AD0 for the Am188ER microcon-

troller) can also be used to load system configuration

information into the internal reset configuration regis-

ter. The system information is latched on the rising

edge of RES.

AO15–AO8 (Am188™ER Microcontroller)

Address-Only Bus (output, three-state,

synchronous, level-sensitive)

On the Am188ER microcontroller, the address-only

bus (AO15–AO8) contains valid high-order address bits

from bus cycles t1–t4. These outputs are three-stated

during a bus hold or reset.

On the Am188ER microcontroller, AO15–AO8 combine

with AD7–AD0 to form a complete multiplexed address

bus while AD7–AD0 is the 8-bit data bus.

On the Am188ER microcontroller during a power-on

reset, the AO15–AO8 and AD7–AD0 pins can also be

used to load system configuration information into an

internal register for later use.

AM186 데이터시트(PDF) 30 Page - Advanced Micro Devices

AM186 데이터시트(HTML) 30 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL