| 전자부품 데이터시트 검색엔진 |
|
CS4218 데이터시트(PDF) 26 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS4218 데이터시트(HTML) 26 Page - Cirrus Logic |
|
26 / 44 page ![]() Power Supply and Grounding The CS4218, along with associated analog cir- cuitry, should be positioned in an isolated section of the circuit board, and have its own, separate, ground plane. On the CS4218, the analog and digital grounds are internally connected; there- fore, the AGND and DGND pins must be externally connected with no impedance between them. The best solution is to place the entire chip on a solid ground plane as shown in Fig- ure 23. Preferably, it should also have its own power plane. The +5V (or +3.3V) supply must be connected to the CS4218 via a ferrite bead, positioned closer than 1" to the device. If using +5V for VD, the VA supply can be derived from VD, as shown in Figure 8. Alternatively, a sepa- rate +5V analog supply may be used for VA, in which case, the 2.0 Ω resistor between VA and VD should be removed. A single connection be- tween the CS4218 ground (analog ground) and the board digital ground should be positioned as shown in Figure 23. Figure 24 illustrates the optimum ground and de- coupling layout for the CS4218 assuming a surface-mount socket and leaded decoupling ca- pacitors. Surface-mount sockets are useful since the pad locations are identical to the chip pads; therefore, assuming space for the socket is left on the board, the socket can be optional for pro- duction. Figure 24 depicts the top layer, containing signal traces, and assumes the bottom or inter-layer contains a fairly solid ground plane. The important points are that there is solid ground plane under the codec on the same layer as the codec and it connects all ground pins with thick traces providing the absolute lowest imped- ance between ground pins. The decoupling capacitors are placed as close as possible to the device which, in this case, is the socket bound- ary. The lowest value capacitor is placed closest to the codec. Vias are placed near the AGND and DGND pins, under the IC, and should attach to the solid ground plane on another layer. The negative side of the decoupling capacitors should also attach to the same solid ground plane. Traces and vias bringing power to the codec should be large, which minimizes the impedance. Although not shown in the figures, the trace lay- ers (top layer in the figures) should have ground plane fill in-between the traces to minimize cou- pling into the analog section. If using all surface-mount components, the de- coupling capacitors should be placed on the same layer as the codec and in the positions shown in Figure 25. The vias shown are as- sumed to attach to the appropriate power and ground layers. Traces and vias bringing power to the codec should be as large as possible to mini- mize the impedance. If using a through-hole socket, effort should be made to find a socket with minimum height, which will minimize the socket impedance. When using a through hole socket, the vias un- der the codec in Figure 24 and 25 are not needed since the pins serve the same function. CS4218 26 DS135F1 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |