| 전자부품 데이터시트 검색엔진 |
|
UCD3138128 데이터시트(PDF) 12 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
UCD3138128 데이터시트(HTML) 12 Page - Texas Instruments |
|
12 / 80 page ![]() UCD3138128, UCD3138A64 SLUSBZ8A – JUNE 2014 – REVISED SEPTEMBER 2014 www.ti.com Timing Characteristics (continued) V33A = V33D = V33DIO = 3.3V; 1 μF from BP18 to DGND, TJ = –40°C to 125°C (unless otherwise noted) PARAMETER TEST CONDITION MIN TYP MAX UNIT Program time to write one word in data 40 µs flash Sync-in/sync-out pulse width Sync pin 256 ns POWER ON RESET AND BROWN OUT (V33A pin, See Figure 3) Time delay after Power is good or tPOR 1 ms RESET* relinquished IRESET goes from a low state to a high The time it takes from the device to exit a state. This is approximately equivalent tEXC1 reset state and begin executing the boot 0.5 ms to toggling the external reset pin from flash.(1) low to high state. IRESET goes from a low state to a high The time it takes from the device to exit a state. This is approximately equivalent tEXC2 reset state and begin executing program 3 ms to toggling the external reset pin from flash bank 0 (32 kB).(1) low to high state. IRESET goes from a low state to a high The time it takes from the device to exit a state. This is approximately equivalent tEXCT reset state and begin executing the total 6 ms to toggling the external reset pin from program flash (64 kB).(1) low to high state. TEMPERATURE SENSOR(1) tON Turn on time / settling time of sensor 100 μs ANALOG COMPARATOR Bits 7 bits INL(3) –0.42 0.21 LSB DNL(3) 0.06 0.12 LSB Time to disable DPWM output based on 0 V to 2.5 V step input on the analog 90 150 ns comparator.(3) (3) Characterized by design and not production tested. 8.7 PMBUS/SMBUS/IC Timing 2 The timing characteristics and timing diagram for the communications interface that supports I2C, SMBus, and PMBus in Slave or Master mode are shown in the Timing Requirements, Figure 1, and Figure 2. The numbers in the Timing Requirements are for 400 kHz operating frequency. However, the device supports two speeds, standard (100 kHz) and fast (400 kHz). 8.8 Timing Requirements PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Typical values at TA = 25°C and VCC = 3.3 V (unless otherwise noted) fSMB SMBus/PMBus operating frequency Slave mode, SMBC 50% duty cycle 100 400 kHz fI2C I2C operating frequency Slave mode, SCL 50% duty cycle 100 400 kHz Bus free time between start and t(BUF) 1.3 µs stop(1) t(HD:STA) Hold time after (repeated) start(1) 0.6 µs t(SU:STA) Repeated start setup time(1) 0.6 µs t(SU:STO) Stop setup time(1) 0.6 µs t(HD:DAT) Data hold time Receive mode 0 ns t(SU:DAT) Data setup time 100 ns t(TIMEOUT) Error signal/detect(2) 35 ms t(LOW) Clock low period 1.3 µs (1) Fast mode, 400 kHz (2) The device times out when any clock low exceeds t(TIMEOUT). 12 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated Product Folder Links: UCD3138128 UCD3138A64 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |