| 전자부품 데이터시트 검색엔진 |
|
ST16C552AIJ68 데이터시트(PDF) 17 Page - Exar Corporation |
|
|
|||||||||||||||||||||||||||||
ST16C552AIJ68 데이터시트(HTML) 17 Page - Exar Corporation |
|
17 / 39 page ![]() 17 ST16C552/552A Rev. 3.40 A2 A1 A0 Register BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 [Default] Note 5* Printer Port Register Set: Note 3* [X] 0 0 PR[00] bit-7 bit-6 bit-5 bit-4 bit-3 bit-2 bit-1 bit-0 [X] 0 0 PR[00] bit-7 bit-6 bit-5 bit-4 bit-3 bit-2 bit-1 bit-0 [X] 0 1 SR[4F] -Busy -ACK PE SLCT Error -IRQ logic logic State “1” “1” [X] 0 1 IOSEL bit-7 bit-6 bit-5 bit-4 bit-3 bit-2 bit-1 bit-0 [X] 1 0 COM[E0] logic logic logic -INTP -SLCTIN INIT -Auto -STROBE “1” “1” “1” Enable FDXT [X] 1 0 CON[00] [X] [X] PD 0-7 -INTP -SLCTIN INIT -Auto -STROBE IN/OUT Enable FDXT Note 1* The General Register set is accessible only when CS A or CS B is a logic 0. Note 2* The Baud Rate register set is accessible only when CS A or CS B is a logic 0 and LCR bit-7 is a logic 1. Note 3*: Printer Port Register set is accessible only when -CSP is a logic 0 in conjunction with the states of the interface signal BIDEN and Printer Control Register bit-5 or IOSEL register. Note 5* The value between the square brackets represents the register’s initialized HEX value, X =N/A. MODEM (UART) REGISTER DESCRIPTIONS Transmit (THR) and Receive (RHR) Holding Reg- isters The serial transmitter section consists of an 8-bit Transmit Hold Register (THR) and Transmit Shift Register (TSR). The status of the THR is provided in the Line Status Register (LSR). Writing to the THR transfers the contents of the data bus (D7-D0) to the THR, providing that the THR or TSR is empty. The THR empty flag in the LSR register will be set to a logic 1 when the transmitter is empty or when data is transferred to the TSR. Note that a write operation can be performed when the transmit holding register empty flag is set (logic 0 = FIFO full, logic 1= at least one FIFO location available). The serial receive section also contains an 8-bit Receive Holding Register, RHR. Receive data is removed from the 552/552A and receive FIFO by reading the RHR register. The receive section pro- vides a mechanism to prevent false starts. On the falling edge of a start or false start bit, an internal receiver counter starts counting clocks at the 16x clock rate. After 7 1/2 clocks the start bit time should be shifted to the center of the start bit. At this time the start bit is sampled and if it is still a logic 0 it is validated. Evaluating the start bit in this manner prevents the receiver from assembling a false charac- ter. Receiver status codes will be posted in the LSR. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |