ST16C552AIJ68 datasheet(19/39 Pages) EXAR

19 / 39 page

ST16C552/552A

Rev. 3.40

IER BIT 6-7:

Not Used - initialized to a logic 0.

FIFO Control Register (FCR)

This register is used to enable the FIFO’s, clear the

FIFO’s, set the receive FIFO trigger levels, and select

the DMA mode. The DMA, and FIFO modes are

defined as follows:

DMA MODE

Mode 0

Set and enable the interrupt for each

single transmit or receive operation, and is similar to

the ST16C450 mode. Transmit Ready (-TXRDY) will

go to a logic 0 when ever an empty transmit space is

available in the Transmit Holding Register (THR).

Receive Ready (-RXRDY) will go to a logic 0 when-

ever the Receive Holding Register (RHR) is loaded

with a character.

Mode 1

Set and enable the interrupt in a block

mode operation. The transmit interrupt is set when the

transmit FIFO is below the programmed trigger level.

-TXRDY remains a logic 0 as long as one empty FIFO

location is available. The receive interrupt is set when

the receive FIFO fills to the programmed trigger level.

However the FIFO continues to fill regardless of the

programmed level until the FIFO is full. -RXRDY

remains a logic 0 as long as the FIFO fill level is above

the programmed trigger level.

FCR BIT-0:

Logic 0 = Disable the transmit and receive FIFO.

(normal default condition)

Logic 1 = Enable the transmit and receive FIFO. This

bit must be a “1” when other FCR bits are written to or

they will not be programmed.

FCR BIT-1:

Logic 0 = No FIFO receive reset. (normal default

condition)

Logic 1 = Clears the contents of the receive FIFO and

resets the FIFO counter logic (the receive shift regis-

ter is not cleared or altered). This bit will return to a

logic 0 after clearing the FIFO.

FCR BIT-2:

Logic 0 = No FIFO transmit reset. (normal default

condition)

Logic 1 = Clears the contents of the transmit FIFO and

resets the FIFO counter logic (the transmit shift regis-

ter is not cleared or altered). This bit will return to a

logic 0 after clearing the FIFO.

FCR BIT-3:

Logic 0 = Set DMA mode “0”. (normal default condi-

tion)

Logic 1 = Set DMA mode “1.”

Transmit operation in mode “0”:

When the 552/552A is in the ST16C450 mode (FIFO’s

disabled, FCR bit-0 = logic 0) or in the FIFO mode

(FIFO’s enabled, FCR bit-0 = logic 1, FCR bit-3 = logic

0) and when there are no characters in the transmit

FIFO or transmit holding register, the -TXRDY pin will

be a logic 0. Once active the -TXRDY pin will go to a

logic 1 after the first character is loaded into the

transmit holding register.

Receive operation in mode “0”:

When the 552/552A is in mode “0” (FCR bit-0 = logic

0) or in the FIFO mode (FCR bit-0 = logic 1, FCR bit-

3 = logic 0) and there is at least one character in the

receive FIFO, the -RXRDY pin will be a logic 0. Once

active the -RXRDY pin will go to a logic 1 when there

are no more characters in the receiver.

Transmit operation in mode “1”:

When the 552/552A is in FIFO mode ( FCR bit-0 =

logic 1, FCR bit-3 = logic 1 ), the -TXRDY pin will be

a logic 1 when the transmit FIFO is completely full. It

will be a logic 0 if one or more FIFO locations are

empty.

Receive operation in mode “1”:

When the 552/552A is in FIFO mode (FCR bit-0 = logic

1, FCR bit-3 = logic 1) and the trigger level has been

reached, or a Receive Time Out has occurred, the -

RXRDY pin will go to a logic 0. Once activated, it will

go to a logic 1 after there are no more characters in the

FIFO.

ST16C552AIJ68 데이터시트(PDF) 19 Page - Exar Corporation

ST16C552AIJ68 데이터시트(HTML) 19 Page - Exar Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

데이터시트 다운로드

링크 URL