| 전자부품 데이터시트 검색엔진 |
|
MCP19124-E/MJ 데이터시트(PDF) 51 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP19124-E/MJ 데이터시트(HTML) 51 Page - Microchip Technology |
|
51 / 236 page ![]() 2016 Microchip Technology Inc. DS20005619A-page 51 MCP19124/5 6.12.2 ERROR AMPLIFIER DISABLES The error amplifiers can be disabled such that its output relinquishes control of the loop to the other error amplifier. Since the error amplifier outputs are clamped to each other the disabled amplifier output will follow the enabled amplifier output but will not be in control of the loop. If both error amplifiers are disabled, both outputs are pulled low (no demand). The EADIS bits default to zero and the error amplifiers are enabled during normal operation. REGISTER 6-14: ABECON: ANALOG BLOCK ENABLE CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DIGOEN DSEL2 DSEL1 DSEL0 DRUVSEL EA2DIS EA1DIS ANAOEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ u = Bit is unchanged x = Bit is unknown -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 DIGOEN: DIG Test MUX to GPA0 Connection Control bit 1 = DIG Test MUX output is connected to external pin GPA0 0 = DIG Test MUX output is not connected to external pin GPA0 bit 6-4 DSEL<2:0>: DIG Test MUX Signal Channel Select bits 000 = QRS (output of DESAT comparator) 001 = PWM_L (PWM output after monostable) 010 = PWM (oscillator output from the microcontroller) 011 = TMR2EQ (when TMR2 equals PR2) 100 = OV (overvoltage comparator output) 101 = SWFRQ (switching frequency output) 110 = SDRV_ON_ONESHOT (200 ns one-shot signal to reset WDM logic) 111 = Unimplemented bit 3 DRUVSEL: Selects gate drive undervoltage lockout level 1 = Gate Drive UVLO set to 5.4V 0 = Gate Drive UVLO set to 2.7V bit 2 EA2DIS: Voltage Error Amplifier Disable bit 1 = Disables the voltage error amplifier (Enables Output OV Comparator Protection) 0 = Enables the voltage error amplifier bit 1 EA1DIS: Current Error Amplifier Disable bit 1 = Disables the current error amplifier 0 = Enables the current error amplifier bit 0 ANAOEN: Analog MUX Output Control bit 1 = Analog MUX output is connected to external pin GPA0 0 = Analog MUX output is not connected to external pin GPA0 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |