STM32F303XD datasheet(18/173 Pages) STMICROELECTRONICS

18 / 173 page

Functional overview

STM32F303xD STM32F303xE

18/173

DocID026415 Rev 5

3.7

Power management

3.7.1

Power supply schemes

•

VSS, VDD = 2.0 to 3.6 V: external power supply for I/Os and the internal regulator. It is

provided externally through VDD pins.

•

VSSA, VDDA = 2.0 to 3.6 V: external analog power supply for ADC, DAC, comparators,

operational amplifier, reset blocks, RCs and PLL. The minimum voltage to be applied to

VDDA differs from one analog peripheral to another. Table 3 provides the summary of

the VDDA ranges for analog peripherals. The VDDA voltage level must always be greater

than or equal to the VDD voltage level and must be provided first.

•

VBAT = 1.65 to 3.6 V: power supply for RTC, external clock 32 kHz oscillator and

backup registers (through power switch) when VDD is not present.

3.7.2

Power supply supervisor

The device has an integrated power-on reset (POR) and power-down reset (PDR) circuits.

They are always active, and ensure proper operation above a threshold of 2 V. The device

remains in reset mode when the monitored supply voltage is below a specified threshold,

VPOR/PDR, without the need for an external reset circuit.

•

The POR monitors only the VDD supply voltage. During the startup phase it is required

that VDDA should arrive first and be greater than or equal to VDD.

•

The PDR monitors both the VDD and VDDA supply voltages, however the VDDA power

supply supervisor can be disabled (by programming a dedicated Option bit) to reduce

the power consumption if the application design ensures that VDDA is higher than or

equal to VDD.

The device features an embedded programmable voltage detector (PVD) that monitors the

VDD power supply and compares it to the VPVD threshold. An interrupt can be generated

when VDD drops below the VPVD threshold and/or when VDD is higher than the VPVD

threshold. The interrupt service routine can then generate a warning message and/or put

the MCU into a safe state. The PVD is enabled by software.

3.7.3

Voltage regulator

The regulator has three operation modes: main (MR), low power (LPR), and power-down.

•

The MR mode is used in the nominal regulation mode (Run)

•

The LPR mode is used in Stop mode.

•

The power-down mode is used in Standby mode: the regulator output is in high

impedance, and the kernel circuitry is powered down thus inducing zero consumption.

The voltage regulator is always enabled after reset. It is disabled in Standby mode.

Table 3. External analog supply values for analog peripherals

Analog peripheral

Minimum VDDA supply

Maximum VDDA supply

ADC/COMP

2.0 V

3.6 V

DAC/OPAMP

2.4 V

3.6 V

STM32F303XD 데이터시트(PDF) 18 Page - STMicroelectronics

STM32F303XD 데이터시트(HTML) 18 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL