전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

HD74AC 데이터시트(PDF) 37 Page - Hitachi Semiconductor

부품명 HD74AC
상세설명  HD74AC Series Common Information
PDF  52 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  HITACHI [Hitachi Semiconductor]
홈페이지  http://www.renesas.com/eng
Logo HITACHI - Hitachi Semiconductor

HD74AC 데이터시트(HTML) 37 Page - Hitachi Semiconductor

Back Button HD74AC Datasheet HTML 33Page - Hitachi Semiconductor HD74AC Datasheet HTML 34Page - Hitachi Semiconductor HD74AC Datasheet HTML 35Page - Hitachi Semiconductor HD74AC Datasheet HTML 36Page - Hitachi Semiconductor HD74AC Datasheet HTML 37Page - Hitachi Semiconductor HD74AC Datasheet HTML 38Page - Hitachi Semiconductor HD74AC Datasheet HTML 39Page - Hitachi Semiconductor HD74AC Datasheet HTML 40Page - Hitachi Semiconductor HD74AC Datasheet HTML 41Page - Hitachi Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 37 / 52 page
background image
Design Considerations
36
a: No Termination
b: Series Termination
c: Parallel Termination
d: AC Parallel Termination
e: Thevenin Termination
Figure 8 Termination Schemes
There are several termination schemes which may be used (figure 8). Included are series, parallel, AC
parallel and Thevenin terminations. AC parallel and series terminations are the most useful for low power
applications since they do not consume any DC power. Parallel and Thevenin terminations cause high DC
power consumption.
2.1 Series Terminations
Series terminations are most useful in high-speed applications where most of the loads are at the far end of
the line. Loads that are between the driver and the end of the line will receive a two-step waveform. The
first wave will be the incident wave. The amplitude is dependent upon the output impedance of the driver,
the value of the series resistor and the impedance of the line according to the formula
V
W = VCC · Zoe/(Zoe + RS + ZS)
The amplitude will be one-half the voltage swing if R
S (the series resistor) plus the output impedance (ZS)
of the driver is equal to the line impedance. The second step of the waveform is the reflection from the end
of the line and will have an amplitude equal to that of the first step. All devices on the line will receive a
valid level only after the wave has propagated down the line and returned to the driver. Therefore, all
inputs will see the full voltage swing within two times the delay of the line.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com