| 전자부품 데이터시트 검색엔진 |
|
AD9154 데이터시트(PDF) 99 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD9154 데이터시트(HTML) 99 Page - Analog Devices |
|
99 / 124 page ![]() Data Sheet AD9154 Rev. C | Page 99 of 124 Addr. Name Bits Bit Name Settings Description Reset Access 4 ENABLE_SYNTH Synthesizer Enable. The bit initiates the start-up sequence of the DAC PLL. The start-up sequence is as follows: 0x0 R/W 1. Enable the bias currents. 2. Enable DAC LDO. 3. Wait for LDO to settle. 4. Calibrate DAC PLL charge pump (The DAC charge pump will only calibrate upon the first setting of ENABLE_SYNTH). 5. Calibrate the band of the PLL. 6. Settle and lock. 0 Disable synthesizer including all currents and calibration codes. 1 Power up synthesizer and initiate calibration sequence. [3:0] RESERVED Reserved. 0x0 R 0x084 DACPLL- STATUS 7 CP_ OVERRANGE_H Charge Pump High Overrange. This bit indicates that the charge pump voltage is too high and a recalibration must be applied. 0x0 R 0 Control voltage not too high. 1 Control voltage too high. 6 CP_ OVERRANGE_L Charge Pump Low Overrange. This bit indicates that the charge pump voltage is too low and a recalibration must be applied. 0x0 R 0 Control voltage not too low. 1 Control VOLTAGE too low. 5 CP_CAL_VALID Charge Pump Calibration Valid. This bit indicates that the charge pump has been successfully calibrated. The selection as to whether the charge pump needs to be calibrated upon startup can be found in Register 0x1B9. 0x0 R 0 If CP_CAL_EN low, this stays low. 1 If CP_CAL_EN high (def), this happens when charge pump is calibrated. 4 VCO_CAL_ PROGRESS VCO Calibration in Progress. This bit is high if the VCO calibration is currently occurring. If this bit is high for more than 1 sec there is something wrong with the VCO calibration. 0x0 R 0 VCO not calibrating. 1 VCO calibrating. [3:2] RESERVED Reserved. 0x0 R 1 RFPLL_LOCK PLL Lock bit. This bit is set high by the PLL once the PLL has achieved lock for the count set by LOCK_MODE bits in Register 0x1C0. 0x0 R 1 PLL locked. 0 PLL unlocked. 0 RESERVED Reserved. 0x0 R 0x085 DACINTEGER WORD0 [7:0] BCOUNT Bits[7:0] of the Integer Tuning Word. This bit controls the integer feedback divider for the DAC PLL. The frequency of the DAC clock can be determined by the following equations: 0x6 R/W fDAC = fREF/(REFDIVMODE ) × 2 × BCount fVCO = fREF /(REFDIVMODE ) × 2 × BCount × LODivMode The minimum value is 6. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |