| 전자부품 데이터시트 검색엔진 |
|
ML9092-01TB 데이터시트(PDF) 45 Page - OKI electronic componets |
|
|
|||||||||||||||||||||||||||||
ML9092-01TB 데이터시트(HTML) 45 Page - OKI electronic componets |
|
45 / 66 page ![]() FEDL9092-01 OKI Semiconductor ML9092-01/02/03/04 45/66 Duty Y register setting range and loop range Invalid address setting range 1/8 0 to 7 (00H to 07H) 0 to 7 (00H to 07H) 1/9 0 to 8 (00H to 08H) 0 to 8 (00H to 08H) 1/10 0 to 9 (00H to 09H) 0 to 9 (00H to 09H) This register is reset to “0” when the RESET pin is made low. • Port register A (PTA) set D7 D6 D5 D4 D3 D2 D1 D0 — PTA —: don’t care The port register A set instruction sets the output of port A. When the PTA bit is set to “1”, a “H” level is output from the PA0 pin of general purpose port A. In the same way, when the PTA bit is set to “0”, a “L” level is output from the PA0 pin. If the RESET pin is pulled to a “L” level, the PE bit (bit D2) of the control register is reset to “0”, this register is reset to “0”, and the PA0 pin goes to high impedance. After the reset state is released, if the PTA bit of this register is set to “1” or “0” and then the PE bit is set to “1”, the PA0 pin is released from its high impedance state and a “H” or “L” level that corresponds to the set status of the PTA bit, is output from the PA0 pin. • Port register B (PTB) set D7 D6 D5 D4 D3 D2 D1 D0 — PTB2 PTB1 PTB0 —: don’t care The port register B set instruction sets the output of port B. (Applies to the ML9092-01/04.) When each bit of PTB0 to PTB2 is set to “1”, the PWM signal set in the PWM0 to PWM2 registers is output from each of the PB0 to PB2 pins of the general purpose port B. In the same way, when each bit of PTB0 to PTB2 is set to “0”, each of the PB0 to PB2 pins are pulled to a “L” level. If the RESET pin is pulled to a “L” level, the PE bit (bit D2) of the control register is reset to “0”, this register is reset to “0”, and the PB0 to PB2 pins go to high impedance. After the reset state is released, if the a PWM value is set in the PWM0 to PWM2 registers and then the PE bit is set to “1”, the PB0 to PB2 registers are released from their high impedance state and a PWM waveform is output. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |