DP83821 datasheet(67/86 Pages) NSC

67 / 86 page

www.national.com

4.0 Register Set (Continued)

4.2.31 Receive Descriptor Pointer 1 Register

This register points to the Receive Descriptor for Priority Queue 1.

4.2.32 Receive Descriptor Pointer 2 Register

This register points to the Receive Descriptor for Priority Queue 2.

Tag: RXDP1

Size: 32 bits

Hard Reset: 00000000h

Offset: 00B0h

Access: Read Write

Soft Reset: 00000000h

bit

tag

description

usage

31-3

RXDP1

Receive

Descriptor Pointer

The current value of the receive descriptor pointer for Priority Queue 1. Packets will be

stored in Priority Queue 1 based on the number of priority queues enabled and the

priority field in the VLAN tag. When the receive state machine is idle, software must set

RXDP1 to the address of an available receive descriptor, and then enable the queue by

writing to the RXE bit in the CR with the RXPRI[1] bit set. While the receive state machine

is active, RXDP1 will follow the state machine as it advances through a linked list of

available descriptors. If the link field of the current receive descriptor is NULL (signifying

the end of the list), RXDP1 will not advance, but will remain on the current descriptor. Any

subsequent writes to the RXE bit of the CR register will cause the receive state machine

to reread the link field of the current descriptor to check for new descriptors that may have

been appended to the end of the list. Software should not write to this register unless the

receive state machine is idle. Receive descriptors must be aligned on 64-bit boundaries

(A2-A0 must be zero).

2-0

unused

Tag: RXDP2

Size: 32 bits

Hard Reset: 00000000h

Offset: 00B4h

Access: Read Write

Soft Reset: 00000000h

bit

tag

description

usage

31-3

RXDP2

Receive

Descriptor Pointer

The current value of the receive descriptor pointer for Priority Queue 2. Packets will be

stored in Priority Queue 2 based on the number of priority queues enabled and the

priority field in the VLAN tag. When the receive state machine is idle, software must set

RXDP2 to the address of an available receive descriptor, and then enable the queue by

writing to the RXE bit in the CR with the RXPRI[2] bit set. While the receive state machine

is active, RXDP2 will follow the state machine as it advances through a linked list of

available descriptors. If the link field of the current receive descriptor is NULL (signifying

the end of the list), RXDP2 will not advance, but will remain on the current descriptor. Any

subsequent writes to the RXE bit of the CR register will cause the receive state machine

to reread the link field of the current descriptor to check for new descriptors that may have

been appended to the end of the list. Software should not write to this register unless the

receive state machine is idle. Receive descriptors must be aligned on 64-bit boundaries

(A2-A0 must be zero).

2-0

unused

DP83821 데이터시트(PDF) 67 Page - National Semiconductor (TI)

DP83821 데이터시트(HTML) 67 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

데이터시트 다운로드

링크 URL