| 전자부품 데이터시트 검색엔진 |
|
CS5541 데이터시트(PDF) 15 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS5541 데이터시트(HTML) 15 Page - Cirrus Logic |
|
15 / 26 page ![]() CS5541 DS500PP1 15 2.9 Performing Conversions/Calibrations The CS5541 offers four conversion/self-calibration modes (if a user requires system calibration, this can be accommodated in the system microcontrol- ler). The first mode allows the user to calibrate con- tinuously between each conversion. The second mode allows the user to calibrate once after the command is issued and then continuously convert on the channel selected using the calibration result. The third mode allows the user to skip calibration; however, it performs conversions with the default calibration coefficients. The final mode allows the user to use the previous calibration coefficients to perform continuous conversions on the channel se- lected. The sections that follow detail the differenc- es between the conversion modes. The sections also explain how to decode the conversion word into the respective flag and data bits. 2.9.1 Continuous Calibrations and Conver- sions (reduced output rate) This mode performs an offset and gain calibration prior to each conversion. Note that the effective throughput in this mode is reduced by two as a cal- ibration is performed prior to each conversion. Nevertheless, after the first command instructing the ADC to enter this mode is given, an offset cali- bration is performed followed by a gain calibration. Then the first data conversion is performed. Subse- quent conversions are offset calibration followed by data conversion. Then, a gain calibration is per- formed followed by a data conversion. The ADC repetitively steps through this sequence until a new command is issued. Note: The CS5541 offers self calibration where the ADC calibrates out offset and gain errors due to the ADC itself. Calibration in the CS5541 is used to set the zero and gain slope of the ADC’s transfer function. For the self-calibration of offset, the converter internally ties the inputs of the modulator together and routes them to the VREF- pin as shown in Figure 12. VREF- must be tied to a fixed voltage between VA+ and VA-. For self-calibration of gain, the differential inputs of the modulator are connected to VREF+ and VREF- as shown in Figure 13. Further note that each calibration step (offset or gain) takes one conversion cycle to complete. However, after the ADC is reset, it is functional and can perform measurements without being calibrated (see Perform Continuous Conversions with Default Calibration Coefficients section for details). In this case, the converter will utilize the initialized values of the on-chip registers (Offset = 0, Gain = 1.0) to calculate output words. Any initial offset and gain errors in the internal circuitry of the chip will remain. AIN+ AIN- + - VREF- Figure 12. Self Calibration of Offset. AIN+ AIN- + - VREF+ VREF- + - Reference Figure 13. Self Calibration of Gain. |
|
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |